Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Serial plates are located on the lower front cabinet flange or on the top of the inside compartment liner, dependent on model. • It is recommended that you attach the original sales receipt to this Use & Care Guide. Inspection Remove Packaging Your wine cabinet has been packed for shipment with all parts that could be damaged by movement securely fastened. Before using, be sure all packing materials and tape have been removed. Important Keep your carton packaging until your wine cabinet has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit. Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant. Responsibility for its safe delivery was assumed by the carrier upon acceptance of the shipment. As directed on the side of your packing carton, claims for loss or damage sustained in transit must be made on the carrier as follows: Exterior Damage Make thorough damage notation on your delivery receipt and have driver acknowledge by signature and date. Send a written request asking for an inspection report from carrier. Include the name of carrier representative and the date the inspection was requested. Retain inspection report and receipt for filing of a claim. Concealed Damage This must be reported to the carrier within fifteen days. Obtain inspection report from the carrier. Retain the inspection report for filing the claim. DO NOT RETURN DAMAGED MERCHANDISE TO MANUFACTURER FILE THE CLAIM WITH THE CARRIER. How to Install Your Refrigerated Wine Cabinet Select Location: The proper location will ensure peak performance of your appliance. Choose a location where the unit will be out of direct sunlight and away from heat sources. Best performance will be achieved in a location where the room temperature is maintained between 65. and 90.F. Operating the wine cooler in a room temperature outside this range could result in inconsistent wine storage temperatures. Cabinet Clearance: Ventilation is required for your unit to operate properly. For under counter units this is achieved through the louvers on the lower front toe-grill. Full-height built-in units require ventilation through the fascia grille at the top of the unit. Please keep these areas open and free of obstructions. Your specific model may have additional installation instructions included in your literature package. Please refer to these for specific details regarding installation of your unit. Electrical Connection: Use nominal 115 volt, 60 cycle AC only. DO NOT USE AN EXTENSION CORD Power Supply Cord with 3-Prong Grounding Plug* Grounding Type Wall Receptacle Figure 1 Grounding Method: This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see figure 1). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local codes and ordinances. The third ground prong should not, under any circumstances, be cut or removed. All U.L. listed refrigerated products are equipped with this type of plug. How to Operate Your Refrigerated Wine Cabinet Setting the Control: The total available temperature range of the unit is from the low forties to the mid sixties. The middle range on the control is approximately 55°F. The temperature can be lowered or raised by turning the control clockwise or counterclockwise, respectively. A higher number is colder, a lower number is warmer. The "OFF" position shuts-down the refrigeration system only, it does not turn-off power to the unit. Figure 2 is a typical control knob representation; your graphics may vary slightly dependent upon your specific model. As with any refrigeration product, there will be a slight temperature variance at different locations within the storage compartment. Your appliance is shipped with the control set to the mid-point setting. It is recommended you wait 48-hours after initial loading of bottles to allow compartment temperature to stabilize prior to making control adjustments. If changes to control settings are desired, please wait 24-hours between adjustments to allow the new control settings to stabilize. Typical Control Knob (Your graphics and colors may vary slightly depending on your specific model.) Set-Point Indicator Figure 2 Wine Bottle Storage: The slide-out shelves each hold four(4) to seven(7) standard size bottles depending on your specific model. See Figure 3 for typical recommended wine bottle storage configuration. Rear Bottles (Necks Facing Front) Front Bottles (Necks Facing Rear) Figure 3 On the full-height built-in models shelf locations are provided with additional spacing to accommodate storage of large mag...