Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
136527colderOff4 HVCE15A • Once you have plugged the unit into an electrical outlet, let the unit run for at least 30 minutes to acclimate itself before making any adjustments. During this time the Red Wine light will stay on. Temperature inside the cooler, if not adjusted, will be at 55°-60°F. • The wine cellar can be set to any temperature you desire to accommodate your wine storage requirements. To set the temperature, press both the "White Wine" and "Red Wine" buttons simultaneously and hold for approximately 3 seconds. Now you are in temperature set mode. Decrease the temperature by pushing the "White Wine" button and increase the temperature by pressing the "Red Wine" button. Pressing the appropriate button 3 times will adjust the temperature 3 degrees, press 4 times equals 4 degrees, 5 times equals 5 degrees, and so on. Once you have selected the temperature you desire, push the "On/Off" button. Now the wine cellar is programmed and the LED readout will return to current internal temperature reading. DownWhiteRedUpon / off • There will be a 3 degree variance +/- between the temperature you select and the temperature indicated on the LED readout. This occurs because the wine cellar activates and deactivates trying to maintain your desired temperature. There is often a 10° variance between the top and bottom shelves of the wine cellar. Therefore, if you have set the wine cellar for 50° and have a mix of red and white wines, you may want to put the white wine on the bottom shelf where the temperature will be 45° F, and place the red wine on the top shelf where the temperature will be 55° F. 6 English Shelving (will vary per model purchased) • The shelves are chrome plated or black coated depending on your model purchased. They are designed for flexibility and easy cleaning. The shelves are designed to allow free air movement. Interior Light • To complement the look of your wine collection, a soft light has been built into the wine cellar. The light switch is on the front bottom, or on the electronic control panel depending on the model purchased. Normal Operating Sounds You May Hear • Boiling water, gurgling sounds or slight vibrations that are the result of the refrigerant circulating through the cooling coils. • The thermostat control will click when it cycles on and off. 7 English WINE CELLAR INSTALLATIONS Install Limitations • Do not install your wine cellar in any location not properly insulated or heated e.g. garage etc. Your wine cellar was not designed to operate in temperature settings below 55° Fahrenheit. • Select a suitable location for the wine cellar on a hard even surface away from direct sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc. Any floor unevenness should be corrected with the leveling legs located on the front and rear bottom corners of the wine cellar. Dimensions • Built-in wine coolers need to be ventilated from the front. This feature allows the unit to be built in an enclosed area. The bottom front grille should be clear of all obstructions. This is absolutely necessary for the air to circulate and for the unit to operate efficiently. The dimensions for installation are as follows. (W x D x H) Unit Dimensions: 14 7/8” x 23 1/8” x 34 1/4” Built-In Dimensions: 15” x 24” x 34 1/2” 20-5/8” 14-7/8” 34-1/4” 23-1/8” 8 English upper hingebracketbottom hingebracketlower doorbracketHVC15A Door Reversal 1. Using a Phillips screw driver remove the upper hinge bracket by removing the screws and the hinge cover on the bracket. (on the right side). 2. Lift and remove the door. 3. Remove the bottom hinge bracket by removing the 3 hexagonal nuts. Be careful not to loose the door level rings which are placed in the hinge bracket axle. (right side). 4. Remove the lower door as shown in figure and install on opposite side. 5. To install the bottom hinge bracket on the opposite side (left side), you will also have to remove screw hole plug from the left side. 6. Carefully align the bottom hinge axle hole on the door with the axle of the lower hinge bracket. Remember to have the door level rings in place before you place the door on its axle. 7. Install the upper hinge bracket on the left side. 8. Make sure the door is aligned and then tighten the screws. • For the HVCE15A remove and reinstall the door handle on the opposite side. Replacing Light Bulb 1. Turn off and unplug the power cord of the wine cellar. 2. To remove the light bulb cover use a Phillips screw driver to remove the 3 screws. 3. Make sure the light bulb is cool before removing it. Replace using a light bulb 10 watts or less. 4. After the bulb is secure, install the light bulb cover and replace the three screws. 5. Turn unit on to its original setting after plugging in the power cord. 9 English PROPER WINE CELLAR CARE AND CLEANING Cleaning and Maintenance Warning: • To avoid electric shock always unplug your wine cellar before cleaing. Ignoring this warning may result in death or injury. Caution: ...
Este manual também é adequado para os modelos :Dispensadores - HVCE15A (203.07 kb)