Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
The wine cellar door will close easier when the leveling legs are extended. Electrical Requirements • Make sure there is a suitable power outlet (115 volts, 15 amps outlet) with proper grounding to power the wine cellar. • Avoid the use of three plug adapters or cutting off the third grounding in order to accommodate a two plug outlet. This is a dangerous practice since it provides no effective grounding for the wine cellar and may result in shock hazard. Use of Extension Cord • Avoid the use of an extension cord because of potential safety hazards under certain conditions. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot outlet that will accept the plug. The marked rating of the extension cord must be equal to or greater than the electrical rating of the appliance. English WINE CELLAR FEATURES AND USE Initial Setup HVCE15 / HVCE24 • Once you have plugged the unit into an electrical outlet, let the unit run for at least 30 minutes to acclimate itself before making any adjustments. During this time the Red Wine light will stay on. Temperature inside the cooler, if not adjusted, will be at 55°-60°F. • The wine cellar can be set to any temperature you desire to accommodate your wine storage requirements. To set the temperature, press both the “White Wine” and “Red Wine” buttons simultaneously and hold for approximately 3 seconds. Now you are in temperature set mode. Decrease the temperature by pushing the “White Wine” button and increase the temperature by pressing the “Red Wine” button. Pressing the appropriate button 3 times will adjust the temperature 3 degrees, pressing 4 times equals 4 degrees, 5 times equals 5 degrees, and so on. Once you have selected the temperature you desire, push the "On/Off" button. Now the wine cellar is programmed and the LED readout will return to current internal temperature reading. • There will be a 3 degree variance +/-between the temperature you select and the temperature indicated on the LED readout. This occurs because the wine cellar activates and deactivates trying to maintain your desired temperature. There is often a 10° variance between the top and bottom shelves of the wine cellar. Therefore, if you have set the wine cellar for 50° and have a mix of red and white wines, you may want to put the white wine on the bottom shelf where the temperature will be 45° F, and place the red wine on the top shelf where the temperature will be 55° F. Temperature English Shelving (will vary by model purchased) • The shelves are chrome-plated glide-out with wood trim. They are designed for flexibility and easy cleaning. The shelves are designed to allow free air movement. Interior Light • To complement the look of your wine collection, a soft light has been built into the wine cellar. The light switch is on the front bottom, or on the electronic control panel. Normal Operating Sounds You May Hear • Boiling water, gurgling sounds or slight vibrations that are the result of the refrigerant circulating through the cooling coils. • The thermostat control will click when it cycles on and off. WINE CELLAR INSTALLATIONS Installation Limitations • Do not install your wine cellar in any location not properly insulated or heated, e.g. garage etc. Your wine cellar was not designed to operate in temperature settings below 55. Fahrenheit. • Select a suitable location for the wine cellar on a hard, even surface away from direct sunlight or heat source, e.g. radiators, baseboard heaters, cooking appliances etc. Any floor unevenness should be corrected with the leveling legs located on the front and rear bottom corners of the wine cellar. Dimensions • Built-in wine cellars need to be ventilated from the front. This feature allows the unit to be built-in in an enclosed area. The bottom front grille should be clear of all obstructions. This is absolutely necessary for the air to circulate and for the unit to operate efficiently. The dimensions for installation are as follows (WxDxH): English Unit Dimensions MODEL W D1 D2 H HVCE15 14-7/8" 20-5/8" 22-1/8" 34-1/4" HVCE24 23-7/8" 21-15/32" 22-15/16" 34-1/4" Built-In Dimensions MODEL W D H HVCE15 15" 24" 34-1/2" HVCE24 24" 24" 35" 22-1/8" 14-7/8"20-5/8" 34-1/4" 34-1/4" 22-15/16" 23-7/8"21-15/32" 9 Door Reversal 1. Upper Hinge Hole Cover 1 2. Upper Hinge Hole Cover 2 3. Upper Hinge Screw Cover 4. Upper Hinge Cover Screw 5. Hinge Cover 6. Upper Hinge Screw 7. Upper Hinge 8. Lower Hinge 9. Lower Hinge Screw 10. Lower Hinge Cover 11. Door Seal 12. Hole Cover 13. Upper Hinge Axes Bushing 14. Door Bushing 15. Axis Bushing Screw 16. Lower Hinge Axes Bushing 17. Handle 18. Spring Gasket 19. Flat Gasket 20. Handle Screw 1. Remove the screw cover from the upper hinge cover. Use a Phillips head screwdriver to remove the screw that holds the upper hinge cover in place. Remove the upper hinge cover. Loosen and remove the screws that hold the upper hinge in place. Note: Make sure you hold door ...
Este manual também é adequado para os modelos :Dispensadores - HVCE24 (429.25 kb)