Light Tube Replacement WARNING! DISCONNECT THE POWER CORD BEFORE ATTEMPTING LIGHT TUBE REPLACEMENT. Failure to do so may result in an electrical shock that could severely injure you. This product uses two, 6 watt light tubes to illuminate the interior of the wine chiller. The light tubes are very reliable electrical components, but should either or both light tubes not function properly, please call the dealer you purchased your wine chiller from for replacement light tubes. Use only original eq

60139 Phone: 1-800-238-3600 Fax: 800-258-0255 August 1995 Printed in the U.S.A. Document No. 18489 Revision No. 02 EJ1 Replacement Parts List Be sure to give dispenser serial and model number when you order replacement parts. EJ1 Bowl Components Item# Part# Description 1 S2722 Spray Tube 2 S2721 Impella Assembly (beige) 1 /n" circulation hole •3 A3058 Impella & Support Pin 4 A2549 Impella Support Pin w/Ciip 5 S4206 Pinch Tube 6 S4467 8 Gallon Bowl (pinch tube type) 7 S4381 Handle A

2 oz (175 g) Ice bank.....................6-8 lb CABINETRY..................High impact plastic cabinetry with stainless steel front panel DISPENSER DIMENSIONS......29 . 3"H x 10 . 4"W x 24 . 3"D (74.4 cm x 26.4 cm x 61.7 cm) WEIGHT.....................Dry: 96 lb (43 . 5 kg) Operating: 136 lb (61. 7 kg) Shipping: 120 lb (54 .4 kg) RECOMMENDED CLEARANCE .. Back: 4" (10 . 16 cm) Top: 12" (30.48 cm) Sides: 1" (2 54 cm) WATER CONNECTION......... 0.375" (. 95 cm) SAE male flare SAE fittin

2232MS) INSTALLATION AND SERVICE MANUAL MANFACTURED BY IMI CORNELIUS INC. ANOKA, MINNESOTA 55303–1592 BEVERAGE CONTROL PANEL ASS’Y Manual Part No. 0713 June 5, 1991 Revised: April 23, 1992 Control Code A THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before the installation and operation of this Equipment. IMI Cornelius Inc. 1990–92 Printed in U.S.A. GENERAL DESCRIPTION Warranty Registration Data (to be filled out by customer) Model Number; Serial Number; In

Purpose of the Voltage Protector Module is to shut the Dispenser down should a too low or a too high power voltage condition occur. Retain these instructions as part of your equipment manual. LOOSE-SHIPPED PARTS Note: Only qualified personnel should install this Kit. Unpack and inspect kit. Make sure items are present and in good condition. Table 1. Loose-Shipped Parts Item No. Part No. Name Qty 1 XXXXXXXXX Voltage Protector Module 1 2 560003334 Electrical Wire (brown) 1 3 560003335 E

WIRING DIAGRAM 2

The purpose of the Keyed Lock-Out Switch is to shut off electrical power to the dispensing valves to prevent dispensing of product. Retain these instructions as part of your equipment manual. LOOSE-SHIPPED PARTS Note: Only qualified personnel should install this Kit. Unpack and inspect kit. Make sure items are present and in good condition. Table 1. Loose-Shipped Parts Item No. Part No. Name Qty 1 560003869 Wiring Harness 1 2 560003870 Template, Hole Drilling 1 3 318948000 Lock Key 1

WIRING DIAGRAM 2

326142000 April 24, 1989 Revised: February 10, 1992 THIS DOCUMENT CONTAINS IMPORTANT INFORMATION This Manual must be read and understood before installing or operating this equipment TABLE OF CONTENTS Page GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . .