Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
[16:9] Select when a 16:9 wide TV is connected. Display Mode The Display Mode setting works only when the TV Aspect mode is set to 4:3. 3 To select another language, press numeric buttons and then b ENTER to enter the corresponding 4-digit number according to the language code list on the page 36. If you enter the wrong language code, press CLEAR. [Off (for Disc Subtitle)] Turn off Subtitle. [Letterbox] Displays a wide picture with bands on the upper and lower portions of the screen. [Panscan] Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (If the disc/file is not compatible with Pan Scan, the picture is displayed at Letterbox ratio.) System Setting Certain speaker settings are prohibited by the Dolby Digital licensing agreement. , 20 System Setting 3 System Setting Outputs 1080 lines of interlaced video. set the Distance between the speakers and 3. Use AD to select the desired speaker. 4. Adjust options using WSAD buttons. 5. Returns to the previous menu by pressing x BACK. Resolution Sets the output resolution of the Component and HDMI video signal. Refer to “Resolution Setting” for details about the resolution (page 14). [Auto] If the HDMI OUT jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. If the COMPONENT VIDEO OUT is only connected, this changes the resolution to 480i (or 576i) as default resolution. [1080p] Outputs 1080 lines of progressive video. [1080i] [Speaker] Select a speaker that you want to adjust. Note [Size] Since the speaker settings are fixed, you cannot change the settings. [ Volume] Adjust the output level of each speaker. [Distance] After you connected speakers to your unit, [720p] Outputs 720 lines of progressive video. [480p (or 576p)] Outputs 480 (or 576) lines of progressive video. [480i (or 576i)] Outputs 480 (or (576) lines of interlaced video. Audio 5.1 Speaker Setup Make the following settings for the built-in 5.1 channel surround decoder. 1. Select [5.1 Speaker Setup] on the [Audio] menu. 2. Press bENTER. The [5.1 SPEAKER] appears. your listening point if the distance of Center or Rear speakers is bigger than the distance of Front speakers. This allows the sound from each speaker to reach the listener at the same time. Press AD to adjust the Distance of the selected speaker. This distance is equivalent to a difference of the distance between Center or Rear speaker and Front speakers. [Test] Select [Speaker Test Start] by using the WS and press b ENTER. Press bENTER again to stop. Adjust the volume to match the volume of test signals memorized in the system. System Setting 21 DRC (Dynamic Range Control) Make the sound clear when the volume is turned down (Dolby Digital only). Set to [On] for this effect. HD AV Sync Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use WS (on the remote control) to scroll up and down through the delay amount, which you can set at anything between 0 and 300m sec. Lock (Parental Control) Initial Setting the Area Code: When you use this unit for the first time, you have to set the Area Code. 1. Select the [Lock] menu and then press D. 2. Press D. To access the [Lock] options, you must input the password you have created. Input a password and press bENTER. Enter it again and press b ENTER to verify. If you make a mistake before pressing bENTER, press CLEAR. 3. Select the first character using WS buttons. 4. Press bENTER and select the second character 3 using WS buttons. 5. Press b ENTER to confirm your Area code selection. Rating Blocks playback of rated DVDs based on their contents. Not all discs are rated. 1. Select [Rating] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select a rating from 1 to 8 using the WS buttons. System Setting [Rating 1-8] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. [Unlock] If you select unlock, parental control is not active and the disc plays in full. 4. Press bENTER to confirm your rating selection. If you forget your password, you can clear it using the following steps: 1. Select the [Setup] menu on the [Home Menu]. 2. Input the 6-digit number “210499” and press b ENTER. The password is cleared. , 22 System Setting 3 System Setting your registration. [Register] Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 35. 1. Select [Area Code] on the [Lock] menu then press D. 2. Input a password and press b ENTER. 3. Select the first character using WS buttons. 4. Press b ENTER and select the second character using WS buttons. 5. Press bENTER to confirm your Area code selection. Displays the registration code of your player. [Deregister] Deactivate your player and display the deactiv...