Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Frame Parts x 6 pcs (4 top/bottom frame pcs. + 2 side frame pcs) 2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods) 3. Screen Material x 1 pc 4. Center joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall brackets x 2 – 3 pcs (depending on model/size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1 – 2 pc s (depending on model/size) 10. Support joiner x 2 – 4 pcs (depending on model/size) 11. Fix Plates x 30 – 90 pcs (depending on model/size) 12. Black cloth backing x 1 pc (AcousticPro1080 models only) Note: Please make sure all parts are included in your package before proceeding to assemble your Elite Screens fixed frame projection screen. ASSEMBLING THE FRAME 1. Insert the center joint connector to the horizontal frame piece and then fasten it with 2 screws 2. Insert the other horizontal frame piece to the center joint connector and then fasten it with 2 screws. 1/2Long frame Push (1) Please do not tighten the screws completely, to make sure the frame piece lines up correctly. 3. Insert both elbow joint connectors into the long horizontal frame (see fig.1) PushPushJointLong frame( fig.1) 4. PushPushShort frameShort frame (2) 4. Join all four frame parts together following the steps showed below. (fig.2) PushPush( fig.2) Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles 5. After making sure that all four corners join at right angles to form a perfect rectangle, fasten the four angles together by using the (x8) joint screws included. (see fig.3) Screw( fig.3) (3) Attaching the screen material to the frame 1. Lay out the screen and tension rods on a clean and dry surface. Insert the screen tension rods through the sleeves according to their corresponding lengths on each edge of the screen as seen below. (see fig.4) Tension Rod (Horizontal) x 4 Tension Rod (Vertical) x 2 5 Steel rodPush( fig.4) Steel rodScreenPush Tension Rod (horizontal) Rod Rod Tension Rod (Vertical) Push 2. Place the screen material on the back of the built frame and slip the tension rods into the grooves running along each side on the back of the frame on all four corner and clip on the fix plates to the back of the frame to secure the rods into place creating tension for a tight and flat surface (see fig. 5 & fig. 6) Push( fig.5) Viewing surface(Front of screen) Steel rodfix plate (fig. 5) (fig. 6) Tension Rod (4) Black backing for AcousticPro1080 models This procedure only applies to AcousticPro1080 models, disregard if your ezFrame is not an AcousticPro1080 variant. The black backing counters the effects of light penetration that would otherwise light up all items behind the screen and spoil the picture. The black backing goes behind the projection surface and are held into position by Velcro-faced fix plates. Fix plate secures AcousticPro1080 material and the black backing behind it. Black backing AcousticPro1080 Screen Material Cover by Black backing Black backing for AcoousticPro1080 material Fix Plate (fig.6) Tension Rod (stretches the AcousticPro1080 material) After the material has been installed, the backing will lay over the back of the white (AcousticPro1080) material and then be held into place by the fix plates as they are added (Fig.1-3). Interval markings reveal the best likely points of attachment (Fig. 1). The prongs on the fix plates (Fig. 2) straddle a lip on the back of the frame creating a friction hold that will firmly keep the material and backing in place (Fig. 3-4). Fig. 1 Fig. 2 *An alternate way to attach the black backing is to utilize the Velcro tabs attached to the tops of the fix plate’s tail (Fig. 4). The material will grab and hold tight to the Velcro as it lays over the tails of the fix plates themselves and stretched from tab to tab around all four sides. Fig. 4 Fig. 3 (5) Attaching the Fix Plates___ 1. Make sure that the material and frame are both lying face down on a clean, dry and non-abrasive surface. 2. Center the material inside the frame. Please note the material will be noticeably smaller because stretching the material is required to create a sufficient amount of tension for perfect material flatness. 3. Start attaching the fix plates in the center of the long horizontal edge and (1) then alternate with the center short sides (2) as shown in diagram (fig.7). Note: Follow these instructions to make sure the material is properly fixed in the center position of the frame. After attaching the fix plates in sequence #2 (the center of the short sides), please remove the fix plates in sequence #1 (the center of the long horizontal edge) and reattach them again, and also remove the fix plates on sequence# (2) and reattach them again. 4. Then continue to follow our recommended order numbers 3-8 to properly distribute tension to the screen material. (Fig. 7) Center Support Bard 1. Insert the support joiner into each side of the center support bar to complete assembly. support joiner Cen...