Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
To use the screwdriver function, in5. sert the Bit Adapter into the Chuck as detailed in Step 1. Insert the required screwdriver bit into the Bit Adapter. Set the drilling torque by turning the 6. Torque Control (6) so that it lines up with the Arrow on the center top of the Cordless Drill/Driver. When driving screws, start with a 7. lower torque setting. When drilling in light gauge metal or 8. wood, use a wooden block to back up the material and prevent damage to the workpiece. Mark the center of the hole to be 9. drilled with a center punch (not included) to give a Drill Bit a starting point and to prevent it from “walking”. Lubricate the Drill Bit with cutting oil 10. (not included) when drilling iron or steel. Use a coolant (not included) when drilling nonferrous metals such as copper, brass, or aluminum. Insert the fully charged Battery Pack 11. into the Handle of the Drill/Driver. The Direction Lever (38) allows you 12. to change the rotational direction of the Drill/Driver. For a clockwise rotation, move the Lever forward. For a counterclockwise rotation, move the Lever back. The center position locks the Trigger (61), to prevent the Drill/ Driver from operating. CAUTION: Never attempt to change rotational direction while Chuck is rotating. Hold the Cordless Drill/Driver firmly 13. with both hands, as torque from the Motor can cause the tool to twist. Operate Drill by squeezing Trigger. 14. The speed of can be controlled by varying the pressure on the Trigger. If the clutch starts slipping before the 15. screw is in all the way, stop the drill, put the Direction Lever in the center position and change the torque setting. Reset the rotation direction before continuing. If Drilling:16. Use the Drill torque setting, as described above. Drill only as deep as necessary. Do not drill deeper than necessary into walls or other areas where you cannot identify any possible hazards behind the drilling surface. To reduce jamming as the Bit breaks through the workpiece, decrease the drilling pressure when the point of the Bit breaks through the workpiece. When you have drilled the hole, 17. remove the Bit from the hole while the Cordless Drill is still running. This prevents the Bit from getting caught in the hole and causing damage. Release Trigger to stop the Drill, put 18. Direction Lever in the center position, and remove the bit from the Drill. Cleaning and Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Set the Direction Lever (38) to the center locked position and unplug the battery from the tool before performing inspection, maintenance, or cleaning procedures. Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. After Use,2. clean external surfaces of the tool with clean cloth. BEFORE EACH USE,3. inspect the general condition of the Cordless Drill/Driver. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. After each use: 4. With a soft brush or cloth, remove all dirt and debris from the Cordless Drill/Driver. Do not immerse the Cordless Drill/Driver in any liquids. The lithium battery in this tool 5. must be recycled or disposed of properly. Parts List Part Description Qty. 1 Screw (M6 x 16) 1 2 3/8” Keyless Chuck 1 3 Screw (M2.2 x 12) 4 4 Mounting Plate 1 5 Spring Holder 1 6 Torque Control 1 7 Sleeve 1 8 Torque Spring 1 9 C-Ring 1 10 Washer 1 11 Ball 15 12 Washer 1 13 Clutch Washer 1 14 Ball 16 15 Bushing 1 16 Gear Housing 1 17 Output Shaft 1 18 Ring Gear 1 19 Planet Gear 6 20 Sun Gear 1 21 Washer 1 22 Screw (M3x6) 2 23 Mounting Bracket 1 24 Screw (M2.2x12) 4 25 Motor Pinion 1 26 Motor 1 27 Screw (M2.9x14) 2 28 Housing Cover 1 29 Screw (M2.9x16) 7 30 E-Washer 1 31 Red Wire Parts List Part Description Qty. 32 Black Wire 1 33 Speed Switch 1 34 Rivet 2 35 Positive Contact Plate 1 36 Negative Contact Plate 1 37 Control Contact Plate 1 38 Direction Lever 1 39 Housing Support 1 40 Screw (M2.9x10) 1 41 Recharging Contact Plate 2 42 Heat Sink 1 43 PCB Supporter 1 44 Battery Pack 1 45 Battery Pack Holder 1 46 Lock Spring 1 47 Power Pack Lock 1 48 Screw (M2.2x8) 1 49 Power Pack 1 50 Holder Plate 1 51 Charging Plate 3 52 Screw (M2.2x14 4) 4 53 Power Pack Cover 1 54 Charger Housing 1 55 Spring Plate 1 56 Charger Contact Plate 2 57 Charger 1 58 Charger Stand Support 1 59 Screw (M2.2x14) 4 60 Adapter 1 61 Trigger 1 62 Bit Adapters...