Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
13. Disconnect idle tools. Switch off the power and disconnect the plug from the power point before servicing, when changing accessories such as blades, bits and cutters, and when the tool is not in use. 14. Remove adjusting keys and wrenches. Get into the habit of always checking to see that keys and adjusting wrenches are removed from the tool before switching on. 15. Avoid unintentional starting. Always check that the switch is in the OFF position before plugging in the tool to the power supply. 16. Use outdoor rated extension cords. When a tool is used outdoors, use only extension cords that are intended for outdoor use and are so marked. 17. Stay alert. Watch what you are doing. Use common sense. Do not operate a power tool when you are tired. 18. Check for damaged parts. Before using a tool, check that there are no damaged parts. If a part, such as a guard is damaged, carefully determine if it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, proper mounting and any other conditions that may affect the operation of the tool. A guard or other part that is damaged should be properly repaired or replaced by an authorised service facility, unless otherwise indicated in this Instruction Manual. Defective switches must be replaced by an authorised service facility. Do not use a tool if the switch does not turn the tool on and off correctly. 19. Guard against electric shock. Prevent body contact with grounded objects such as water pipes, radiators, ranges and refrigerator enclosures. 20. Use only approved parts. When servicing, use only identical replacement parts. Use an authorised service facility to fit replacement parts. 21. Warning. The use of any accessory or attachment other than those recommended in this instruction manual, may present a risk of personal injury. 22. Have your tool repaired by a qualified person. This electric tool is in accordance with the relevant safety requirements. Repair should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user. 23. Special safety hints. • Your cordless drill is not charged when purchased. Be sure to charge the unit for fully approximately 5–7 hours prior to initial use. • A battery stored used or charged under high temperature conditions will deteriorate more quickly. • Don’t overcharge the battery. • Once your battery is fully charged, disconnect the charger from the power and store safely in the drill. • Never store the battery out of the drill, as the two contacts on the drill are exposed and could be shorted by a metal object and cause a fire or explosion! • Before drilling check that there are no hidden hazards such as electric cables, water or gas pipes running below the surface-use a metal/voltage detector. • Don’t expose either the drill or charger to rain, high humidity or wet conditions. 4 Know your product This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use machine only for intended applications. All other applications are expressly ruled out. 1. Keyless chuck 2. Torque collar 3. Forward/reverse switch 4. Trigger with variable speed control 5. Battery pack release 6. Rechargeable battery pack Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. 7. Adaptor 1 7 2 4 3 5 6 5 Battery charging Connect the adaptor plug to the socket in the rear of the battery (6). Plug the adaptor (7) into a 230–240V mains power point and switch on. The red LED light near the rear of the battery will show that charging is taking place. The normal battery charge time is between 3–5 hours, but an indication as to the battery being fully charged is when the case of the battery starts to warm up. Once this occurs, switch off the adaptor at the 230–240V mains power point and remove the adaptor plug from the rear of the battery. Your drill/driver is ready for use! To keep the best life of the battery, let the battery start to loose its power before charging, but do not let the drill come to a standstill before charging. Do not do short charges but make sure that the battery is fully charged every time it is in need of charging. Warning. Never store the battery out of the drill/driver as the two contacts on top of the battery are exposed and could be shorted by a metal object and cause a fire or explosion! Caution. Never use the drill while charging is in progress! Using the drill Use the forward/reverse switch to select the direction of rotation, then pull the trigger (4) on. This trigger switch is electronic variable speed which enables the user to vary the speed continuously. The speed varies according to how far the trigger switch i...