Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area When operating a power tool outside, use an outdoor extension cord marked "W-A" Keep your work area clean and well lit. or "W." These cords are rated for outdoor use Cluttered benches and dark areas invite and reduce the risk of electric shock. Refer to accidents. “Recommended sizes of Extension Cords” in Do not operate power tools in explosive the Accessory section of this manual. atmospheres, such as in the presence of flammable liquids, gases, or dust. Power Personal Safety tools create sparks which may ignite the dust Stay alert, watch what you are doing and or fumes. use common sense when operating a power tool. Do not use tool while tired or Keep by-standers, children, and visitors under the influence of drugs, alcohol, or away while operating a power tool. medication. A moment of inattention while Distractions can cause you to lose control. operating power tools may result in serious Electrical Safety personal injury. Double Insulated tools are equipped with a Dress properly. Do not wear loose clothing polarized plug (one blade is wider than the or jewelry. Contain long hair. Keep your other.) This plug will fit in a polarized outlet hair, clothing, and gloves away from only one way. If the plug does not fit fully in moving parts. Loose clothes, jewelry, or long the outlet, reverse the plug. If it still does hair can be caught in moving parts. Keep not fit, contact a qualified electrician to handles dry, clean and free from oil and install a polarized outlet. Do not change grease. the plug in any way. Double Insulation Avoid accidental starting. Be sure switch is eliminates the need for the three wire “OFF” before plugging in. Carrying tools withgrounded power cord and grounded power supply system. Before plugging in the tool, be your finger on the switch or plugging in tools that have the switch “ON” invites accidents. certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use Remove adjusting keys or wrenches before“AC only” rated tools with a DC power supply. turning the tool “ON”. A wrench or a key that Avoid body contact with grounded surfaces is left attached to a rotating part of the tool may result in personal injury. refrigerators. There is an increased risk of such as pipes, radiators, ranges and Do not overreach. Keep proper footing and electric shock if your body is grounded. If balance at all times. Proper footing andoperating the power tool in damp locations is balance enables better control of the tool in unavoidable, a Ground Fault Circuit Interrupter unexpected situations. must be used to supply the power to your Use safety equipment. Always wear eye tool. Electrician’s rubber gloves and footwear protection. Dust mask, non-skid safety will further enhance your personal safety. shoes, hard hat, or hearing protection must be Don't expose power tools to rain or wet used for appropriate conditions. conditions. Water entering a power tool will increase the risk of electric shock. Tool Use and Care Use clamps or other practical way to Do not abuse the cord. Never use the cord secure and support the workpiece to a to carry the tools or pull the plug from an stable platform. Holding the work by hand or outlet. Keep cord away from heat, oil, sharp against your body is unstable and may lead to edges or moving parts. Replace damaged loss of control. cords immediately. Damaged cords increase the risk of electric shock. Do not force tool. Use the correct tool for your application. The correct tool will do the -2 BM 1619929510 2/03 2/12/03 12:23 PM Page 3 job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Any alteration or modification is a misuse and may result in a dangerous condition. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your t...