Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
It may also be used to alert against unsafe practices. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. This symbol is used to alert the user to useful information about proper operation of the equipment. NOTICE 1. DRILL INSPECTIONS: Perform drill inspections and maintenance service promptly as required. 2. DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. SHARP SURFACES: DO NOT place hands near, or in contact with, cutting surfaces during operation. 5. DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use pneumatic tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted. 6. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area. 7. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation. Safety Instructions for Hand Drills -C Safety Instructions for Hand Drills 8. USE THE RIGHT TOOL. Do not 16. DISCONNECT TOOLS before serforce tool or attachment to do a job vicing, changing accessories, or for which it was not designed. moving to another location. 9. DO NOT USE UNDER THE 17. DO NOT OVERREACH. Keep INFLUENCE OF DRUGS OR proper footing/balance at all times. ALCOHOL. 18. USE THE RECOMMENDED 10. USE PROPER EXTENSION CORD ACCESSORIES. Consult owner’s for the tool. Make sure your exten-manual for recommended accession cord is in good condition and sories. The use of improper accesis long enough to reach your work sories may cause risk of injury. without stretching. 19. DRILLING. Always apply a steady 11. WEAR PROPER APPAREL. Do and slow pressure on the drill when not wear loose clothing, gloves, drilling. Always expect a drill bit or neckties, rings, bracelets, or other hole saw to grab, and be prepared jewelry which may get caught in to let go of the drill trigger before moving parts. Non-slip footwear is the drill stalls or the bit breaks. recommended. Wear a protective hair covering to contain long hair. 20. NEVER LEAVE UNATTENDED TOOL CONNECTED TO POWER. 12. ALWAYS USE SAFETY GLASSES. Disconnect the tool from the power Also use a face or dust mask if cut-source before leaving the area. ting operation is dusty. Everyday eyeglasses only have impact resis21. NEVER ALLOW UNTRAINED tant lenses, they are NOT safety USERS TO USE THIS TOOL glasses. WHILE UNSUPERVISED. 13. SECURE WORK. Use clamps or a 22. IF YOU ARE UNSURE OF THE vise to hold work when practical. It INTENDED OPERATION, STOP is safer than using your hand and USING TOOL. Seek formal instruc frees both hands to operate tool. tion. 14. TEST RUN. Always test run the drill 23. KEEP DRILL BITS SHARP. before starting any work. Replace or sharpen blade as needed. 15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Do not carry tool with hand on trigger and always disconnect from power when not in use. -D- Model H7859 Right Angle Drill Safety Instructions for Drills 1. READ THROUGH THE ENTIRE 9. DO NOT OVERREACH. Keep MANUAL BEFORE STARTING proper footing and balance at all DRILL. Drill presents serious injury times. hazards to untrained users. 10. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SAFETY GLASSES WHEN SERVICING DRILL. Make sure OPERATING DRILL. Everyday eye- switch is in OFF position before glasses are NOT safety glasses. reconnecting. 2. ALWAYS USE ANSI APPROVED 11. MAINTAIN DRILL WITH CARE. PROOF. Use padlocks, master Keep blades sharp and clean switches, and remove switch keys. for best and safest performance. Follow instructions for lubricating 3. MAKE WORKSHOP CHILD 4. KEEP CHILDREN AWAY. Keep all and changing accessories. children a safe distance from the work area. 12. REMOVE THE CHUCK KEY. Make a habit of checking for the chuck 5. WEAR PROPER APPAREL. DO key before turning drill ON. NOT wear loose clothing, neckties, rings, or jewelry which may 13. DO NOT FORCE DRILL. Work get caught in the drill chuck. Wear at the speed for which the drill or protective hair covering to contain accessory was designed. long hair. 14. SECURE THE WORKPIECE. 6. DO NOT USE IN DANGEROUS Use clamps or a vise to hold ENVIRONMENTS. DO NOT use the workpiece when practical. A drill in damp, wet locations, or secured workpiece protects your where any flammable or noxious hands and frees both hands to fumes may exist. operate the drill. 15. BE AWARE THAT CERTAIN WELL LIT. Clutter and dark shad7. KEEP WORK AREA CLEAN AND WOODS MAY CAUSE AN ALLERows may cause accidents. GIC REACTION in people and animals, especially when exposed to 8. USE A GROUNDED EXTENSION fine dust. Make sure you know CORD RATED FOR THE DRILL what type of wood dust you will be AMPERAGE. Undersized cords exposed to and always wear an overheat and los...