Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
Fits drill press tables with t-nut slots or with slotted through holes as shown in figure 1. figure 1. h8071 drill press lathe attachment specifications tool rest length ............................................ 12" Maximum Workpiece length (if reversed) ..... 24" Maximum Workpiece diameter........................6" shank diameter of screw and spur Center....3.8" Construction Material .................................. steel shipping Weight .......................................3.5 lbs. inventory refer to the list and figure 2 to inventory your package. if you can't find an item on this list, check the mounting locations or examine the packaging materials carefully. occasionally we pre-install certain components for shipping purposes. if any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. description Qty a. tool rest .................................................... 1 b. Cap screw M8-1.25 x 20............................1 c. Cap screw M6-1 x 20................................. 1 d. tool rest Foot ............................................ 1 e. Carriage Bolt M10-1.5 x 40......................... 2 f. Base and live Center assembly................1 g. Flat Washer 10mm ..................................... 2 h. hex Nut M10-1.5.........................................2 i. hex Wrenches 5, 6mm..........................1 Ea J. screw Center.............................................. 1 K. spur Center ................................................ 1 figure 2. inventory. a C B E F d g h i J K Copyright © JUNE, 2010 By grizzly iNdUstrial, iNC. Warning: no portion of this manual may be reproduced in any shape or form Without the Written approval of grizzly industrial, inc. #Cr13012 priNtEd iN ChiNa setup If you need help with your new drill press lathe attachment, call our Tech Support at: (570) 5469663. tools needed Qty Wrench 17mm.................................................... 1 to setup the drill press lathe attachment: 1. at each end of the workpiece, drill an 1.8" pilot hole 5.8" deep. 2. disCoNNECt drill prEss FroM poWEr! 3. Verify that the drill press table is properly leveled, and adjust as required. 4. place the base so the live center is located in the center of the drill press table, as shown in figure 3. Base Drill Press Table Live Center figure 3. Mounting base to drill press table. 5. Fasten the base to the table with the carriage bolts, flat washers, and hex nuts, but do not fully tighten the hex nuts yet. 6. install a drill bit or dowel in the chuck, lower the chuck so the tip of the drill bit or dowel just touches the point of the live center. -2 7. Move the base so the tip of the live center is aligned with the spindle centerline, as shown in figure 4. Next, tighten the base hex nuts. Spindle Centerline and Live Center Aligned figure 4. live center to spindle alignment. 8. retract the drill press spindle, and fasten the tool rest foot onto the base with the cap screw, as shown in figure 5 later. Use the workpiece to estimate where to tighten the tool rest in place to achieve a gap of 1.8" to 1.2" between the workpiece and the tool rest. to1 8. 1 2. Gap Foot Tool Rest "" figure 5. tool rest installation and adjustment. 9. double check that all fasteners are tight. h8071 drill press lathe attachment operation safety read and follow these safety precautions: damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. always wear safety glasses, a respirator, and hearing protection when operating this machine. loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing and long hair away from moving machinery. no list of safety guidelines can be complete. every shop environment is different. always consider safety first, as it applies to your individual working conditions. use this and other machinery with caution and respect. failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results. NOTICE if you have never used this type of machine or equipment before, We strongly recommend that you read books, trade magazines, or get formal training before beginning any projects. regardless of the content in this section, grizzly industrial will not be held liable for accidents caused by lack of training. eye/face protection. Wear eye protection and a face shield during all turning operations. respiratory protection. always wear a respirator when using this tool. Wood dust may cause allergies or long-term respiratory health problems. avoiding entanglement. Keep long hair and loose clothing such as sleeves, belts, and jewelry items away from the workpiece and chuck. WorKpiece condition. always inspect the condition of your workpiece. NEVEr turn stock with knots, splits, and other potentially dangerous conditions. all glued joints must hav...