Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
EYE IN JURY HAZARD ! Wear protective equipment when using these tools. The impact wrench and ratchet requires 90 PSI to operate correctly. To improve air tool lifespan, use the filter/lubricator/regulator setup shown in Figure 2, or install the included in-line lubricator dircectly to the air line. Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator Air Compressor Your Tool Figure 2. Installed filter lubricator regulator. Air Supply impact Wrench your new 1.2" drive impact wrench (figure 3) generates up to 260 ft/lbs. of torque. only use thick-walled impact sockets with this air tool. the common thin-walled chrome sockets may explode if used as impact sockets, causing serious injury. At the end of the handle you can adjust the torque setting by pushing the knob in and turning the knob to 1, 2, 3, or 4; 1 is the lowest torque setting. to change the impact rotation, push the slide button toward the front of the gun for clockwise rotation and to the rear for counterclockwise rotation. torque setting rotation Button figure 3. impact wrench control locations. ratchet your new ratchet (figure 4) generates up to 50 ft/lbs. of torque and delivers up to 160 rpM. to change the rotation, adjust the forward/ reverse dial, as shown in figure 4. Forward/reverse dial figure 4. ratchet locations. daily maintenance your impact wrench and ratchet Must have 2-6 drops of oil directly dropped into the air fitting before each use. in addition, we recommend using an in-line filter, lubricator, and regulator, as shown in figure 2 or the included in-line lubricator. if an in-line lubricator is not used, add 2-3 drops of oil into the tool air inlet every 2 hours of continued use. these procedures should be done after each use: • Before putting the impact wrench or ratchet away, put 2-6 drops of oil into the air supply fitting and momentarily operate the tool to distribute the oil inside. • Wipe the tool exterior and sockets with a slightly oiled cloth. your goal is to leave a light film of oil on the tools to prevent rust. " impact Wrench and ratchet Kit2.1Model g5791/g5792 17-piece -5 impact Wrench .............................................................................................................................. .............................................................. REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P5791001 HOUSING 26 P5791026 ROTOR BLADE 2 P5791002 VALVE BUSHING 27 P5791027 REAR CYLINDER PLATE 3 P5791003 REVERSE VALVE 28 P5791028 BALL BEARING 4 P5791004 TRIGGER 29 P5791029 FRONT CYLINDER PLATE 5 P5791005 ROLL PIN 6 P5791006 VALVE STEM 7 P5791007 AIR INLET 1/4 NPT 8 P5791008 BALL SEAT 9 P5791009 COMPRESSION SPRING 10 P5791010 STEEL BALL 11 P5791011 AIR COVER 12 P5791012 AIR REGULATOR 13 P5791013 O-RING 14 P5791014 COMPRESSION SPRING 15 P5791015 REAR OIL SEAL 16 P5791016 SET SCREW 17 P5791017 BUSHING 18 P5791018 ANVIL 1/2" DRIVE 19 P5791019 HAMMER CAGE 20 P5791020 HAMMER PIN 21 P5791021 HAMMER DOG 22 P5791022 DRIVE CAM 23 P5791023 ROLL PIN 24 P5791024 CYLINDER 25 P5791025 ROTOR 30 P5791030 ROLL PIN 31 P5791031 COMPRESSION SPRING 32 P5791032 PIN 33 P5791033 GASKET 34 P5791034 REAR COVER 35 P5791035 CAP SCREW 36 P5791036 LOCK WASHER 37 P5791037 FRONT RUBBER 38 P5791038 EXAHUST DEFELCTOR 39 P5791039 PHLP HD SCREW 40 P5791040 PILOT SET SCREW 41 P5791041 ANVIL COLLAR 42 P5791042 O-RING 43 P5791043 REAR RUBBER BUMPER 44 P5791044 SET SCREW 45 P5791045 FRONT OIL SEAL *46 P5791046 O-RING KIT 47 P5791047 AIR FITTING 1/4 NPT MALE 48 PAW04M HEX WRENCH 4MM 49 P5791049 IN-LINE LUBRICATOR 50 P5791050 CARRYING CASE * not included with impact wrench or ratchet; for aftermarket purchase only -6 " impact Wrench and ratchet Kit2.1Model g5791/g5792 17-piece ratchet ....( ....+ .........., ....% ...., ...... ...... ..... ....' .......... ....* ...... ....+ ....( ...... ...., ....) ...... ....) ...., .... ........ * ....+ ..... ..... .... ..... ...... ...... ....' ...... ...., ...... ....& ....& ....( ....) ....& ....) ....( ...... ..........' ......* ....( ..... ....% ....& ....' ....( ....) ....* REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P5791101 HOUSING 102 P5791102 AIR INLET 103 P5791103 THROTTLE LEVER 104 P5791104 ROLL PIN 105 P5791105 VALVE BUSHING 106 P5791106 VALVE STEM 107 P5791107 O-RING 108 P5791108 COMPRESSION SPRING 109 P5791109 O-RING 110 P5791110 VALVE PLUG 111 P5791111 END PLATE CAP 112 P5791112 REAR BEARING 113 P5791113 REAR PLATE 114 P5791114 ROTOR 115 P5791115 ROTOR BLADE 116 P5791116 CYLINDER 117 P5791117 CYLINDER PIN 118 P5791118 FRONT PLATE 119 P5791119 FRONT BEARING 120 P5791120 SPECIAL WASHER 121 P5791121 THREAD RING GEAR 122 P5791122 RATCHET HOUSING 123 P5791123 IDLER GEAR 124 P5791124 IDLER GEAR PIN 125 P5791125 IDLER GEAR PLATE 126 P5791126 CLAMP NUT 127 P5791127 BUSHING 128 P5791128 BUSHING 129 P5791129 CRANK SHAFT 130 P5791130 DRIVE BUSHING 131 P5791131 RATCHET YOKE 132 P5791132 RATCHET ANVIL 1/2" DRIVE 133 P5791133 COMPRESSION SPRING 134 P5...