Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
No adapter is available or should be used when the drill press is converted for 230 volts. If the drill press must be reconnected for use on a different type of electrical circuit, the re-connection should be made by qualified service personnel; and after re-connection, the tool should comply with all local codes and ordinances. GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES Fig. C 6 1 234 5 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 1 234 5 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 1. Drill Press Head 2. Column and Table Raising Rack 3. Table/Column Bracket 4. Lock Lever for Column Bracket 1/2-13x1-1/2" 5. Lock Lever for Table 3/8-16x1-1/8" 6. Worm for Table-Raising Mechanism 7. Table-Raising and Lowering Handwheel 8. Table 9. Chuck 10. Chuck Key 11A. Pinion Shaft Handles (3) (For model 17-925 ONLY) 11B. Pinion Shaft Handle (For Model 17-990X ONLY) 12. Speed Range Changing Lever 13. Speed Changing Levers (2) 14. Base 15. M8 x 125mm Carriage Head Screw (2), M8 Flat Washer (2), M8.1 Lock Washer (2), M8 Hex Nut (2) 16. M10 x 40mm Hex Head Screw (4) 17. 5mm Hex Wrench 18. 3mm Hex Wrench 8 gea gages internal gear in the table bracket. ASSEMBLY TOOLS REQUIRED 3mm Hex Wrench (Supplied) 5mm Hex Wrench (Supplied) Adjustable Wrench ASSEMBLY Fig. 4 Fig. 5 G H H G F I Fig. 6 ASSEMBLY TIME ESTIMATE The assembly time for this unit is approximately 1-2 hours. For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. 1. Attach the column (A) Fig. 3 to the base (B) using the four M10x40mm hex head screws (C), three of which are shown. Loosely thread the locking lever (D) into the table mounting bracket (E). Loosen the set screw (D) with the supplied 3mm wrench and remove the ring (E) and raising rack (F). 2. Insert the small end of the worm gear (G) Fig. 4 and Fig. 5, through the hole (H) from the inside of the table bracket. Make certain that the worm gear engages the internal gear in the table bracket. 3. Insert the raising rack (F) Fig. 6 (removed in STEP 1) into the groove in the table bracket (I). Make certain that the teeth of the internal gear, located inside the table bracket, are engaged with the teeth of the raising rack (F). A B C D E Fig. 3 F 4. Slide the raising rack (F) Fig. 7 and table bracket (J) on the drill press column. Make certain that the bottom of the raising rack (F) Fig. 8 is engaged with the flange (K) on the drill press base. FI Fig. 7 F J 9 10 5. Re-install the ring (E) Fig. 9 (removed in STEP 1). IMPORTANT: DO NOT push the ring (E) Fig. 9 all the way down on the the raising rack (F). Make certain that the top of the raising rack (F) is under the bottom of the ring (E) and that enough clearance is available to allow the rack (F) to rotate around the column. Tighten the set screw (D) with the supplied 3mm wrench. Fig. 9 E D S IMPORTANT: Make certain that the spindle taper (Q) Fig. 16 and the tapered hole in the chuck (R) are clean and free of any grease, lacquer, or rust-preventive coatings. NOTE: Household oven cleaner can effectively remove any substance from the spindle and chuck. Carefully follow the manufacturer's safety rules concerning its use. IMPORTANT: Open the chuck jaws as wide as possible with the chuck jaws inside the chuck. 13. Hold the chuck on the taper of the spindle. Set the chuck by tapping it with a soft-tipped hammer (T) or a block of wood and hammer (Fig. 17). To avoid damage to the chuck, NEVER drive the chuck onto the spindle with a metal hammer. Fig. 16 Q R FOR MODEL 17-925 ONLY Thread the three pinion shaft handles (U) in the three holes located in the pinion shaft hub (V) (Fig. 18). FOR MODEL 17-990X ONLY 1. Remove the screw (A) Fig. 19 and the flat washer (B). 2. Place the handle (A) Fig. 20 on pinion shaft (C). Align the key slot (D) in the handle with the key (E) on the pinion shaft. 3. Replace the flat washer (C) Fig. 21 and thread the screw (B) into the pinion shaft. 4. Tighten securely. Fig. 20A D E C Fig. 17 Fig. 18 Fig. 19 Fig. 21 S T V U A B C T 11 5. Thread the two speed-changing levers (W) Fig. 22 into the speed changing hub. 6. Thread the speed range-changing lever (X) Fig. 23 into the hub. Fig. 22 Fig. 23 MOUNTING DRILL PRESS ON A SUPPORTING SURFACE If, during operation, the machine has a tendency to tip over, slide, or walk on the supporting surface, secure the machine base to the supporting surface with an M8x1.25x125mm carriage head screw, 8.5mm flat washer, 8.5mm lock washer, M8x1.25 hex nut through the two holes (A) Fig. 24 located in the machine base. Fig. 24 A MOUNTING THE DRILL PRESS ON A PLYWOOD BASE If you do not fasten your machine permanently, then you must fasten the drill press to a plywood mounting board to prevent it from tipping over. Use a good grade of 3/4" or thicker plywood. DO NOT make the mounting board from particle board. 1. Start with a 21" x 28" or larger piece of plywood. Drill two 3/8...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 17-990X (640.36 kb)