Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
NOTE: The torque adjustment collar may be set on any number and change between screwdriving and drilling modes using the mode control collar. DRILLING (FIG. 3) CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not clutch out regardless of the position of the torque adjustment collar (D). Rotate the mode control collar (C) so the drill symbol is aligned with the arrow. NOTE: The torque adjustment collar (D) may be set on any number. HAMMERDRILLING (FIG. 4) Rotate the mode control collar (C) so the hammer symbol is aligned with the arrow. Torque Adjustment Collar (Fig. 2) Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and a hammer mechanism for drilling into masonry. Circling the torque adjustment collar (D) are numbers. These numbers are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener which can be driven. To select any of the numbers, rotate until the desired number aligns with the arrow. Three-Speed Gearing (Fig. 2) The three-speed feature of your tool allows you to shift gears for greater versatility. To select speed 1 (highest torque setting), turn the tool off and permit it to stop. Slide the gear shifter (E) all the way to the left. Speed 2 (middle torque and speed setting) is in the middle position. Speed 3 (highest speed setting) is to the right. NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete stop before changing gears. If you have trouble changing gears, make sure that the gear shifter is engaged in one of the three speed settings. Self-Tightening Chuck Operation (Fig. 5–7) WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may result. Always lock off trigger switch when changing acces sories. WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject from tool causing possible personal injury. TO INSERT A DRILL BIT OR OTHER ACCESSORY 1. Lock the trigger in the OFF position. 2. Grasp the chuck sleeve (F) with one hand and use the other hand to secure the tool as shown in Figure 5. Rotate the sleeve counterclockwise (viewed from the front) far enough to accept the desired accessory. 3. Insert the bit or other accessory about 3/4" (19 mm) into the chuck, as shown in Figure 6. Grasp the chuck sleeve securely and rotate the sleeve clockwise (viewed from the front) with one hand while using the other hand to secure the tool. Rotate the sleeve clockwise until sleeve cannot be rotated any further, as demonstrated in Figure 7. As the drill is being operated in the forward position, the chuck will continually self-tighten the jaws of the chuck onto the bit to maximize the bit gripping strength. To release the accessory, repeat Step 2. OPERATION WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from battery pack before making any adjustments or removing/installing attachments or accessories. Installing and Removing the Battery Pack (Fig. 8, 9) NOTE: Make sure your battery pack is fully charged. CAUTION: Make certain the lock-off button (B), as shown in Figure 1, is engaged to prevent switch actuation before removing or installing battery. To install the battery pack into the tool handle, align the base of the tool with the rails inside the tool’s handle and slide the battery pack firmly into the handle until you hear the lock snap into place (Fig. 8). To remove the battery pack from the tool, press the release button (G) and firmly pull the battery pack out of the tool handle. Insert it into the charger (Fig. 9) as described in the charger section of this manual. Side Handle WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control. Side handle clamps to the front of the gear case as shown and may be rotated to permit right- or left-hand use. Side handle must be tightened sufficiently to resist the twisting action of the tool if the accessory binds or stalls. Be sure to grip the side handle at the far end to control the tool during a stall. If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the battery pack. Drill Operation 1. Select the desired speed/torque range using the gear shifter to match the speed and torque to the planned operation. 2. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use highspeed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. 3. Always apply pressure in a straight li...
Este manual também é adequado para os modelos :Brocas e shuropopverty - DC910 (1.27 mb)
Brocas e shuropopverty - DC901 (1.27 mb)