Log:
Assessments - 5, GPA: 4.2 ( )

Instruções de Operação Harbor Freight Tools, Modelo PITTSBURGHPRO 239

Fabricante : Harbor Freight Tools
Arquivo Tamanho: 301.96 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during use. 3. Use only within rated torque range. Do not use for loosening. 4. Use as intended only. Do not use as hammer or pry bar. Do not use handle extension to increase force. Do not drop. 5. Inspect before every use; do not use if damaged or if parts are loose. 6. Keep away from children. 7. For your safety, service, calibration, and maintenance should be performed regularly by a qualified technician. 8. Use only sockets with the correct drive and rated to at least the torque that will be applied to it. CauTIOn, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Page 2 For technical questions, please call 1-800-444-3353. SKU 00239 Operating Instructions Operating Instructions Read the enTIRe ImpORTanT SaFeTy InFORmaTIOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Controls Drive Anvil Torque Settings Knurled Handle 1. Lock Knob Wear ANSI-approved safety goggles and heavy-duty work gloves. 2. Clean and/or repair the threads that will be tightened. Damaged or dirty threads will result in a misleading torque reading. 3. Select the desired socket and verify it fits properly on the nut or bolt being tightened. 4. Press the socket firmly onto the drive anvil. Lock Knob 5. Turn the Lock Knob at bottom of the Handle counterclockwise until it stops. 6. Turn the handle to set the torque. To set to 55, for example: 50 2 01 89 70 60 80 (a) a. Turn the knurled handle (CW or CCW) until the “0” graduation on the bevel edge lines up with 50. See illustration (A), above. 50 7 56 34 70 60 80 (B) The 50 line is shown in grey because it will likely be hidden at this point. b. Continue turning the knurled handle about a half turn clockwise until the “5” graduation mark lines up with the centerline. It is now set for 55. See illustration (B), above. SKU 00239 For technical questions, please call 1-800-444-3353. Page 3 7. Retighten the Lock Knob by turning it all the way clockwise. Direction Switch 8. Set the Direction Switch for clockwise or counterclockwise operation. The Switch shown above is in position for clockwise operation. 9. Place socket onto the nut or bolt and pull the handle gradually in the desired direction until a click is heard or felt. Do not pull beyond that point; the click indicates that the torque setting has been reached. 10. Stop pulling and the Torque Wrench will automatically reset. 11. When finished, loosen the lock knob and set the Torque to the lowest torque setting (not lower than the lowest setting) before storing indoors out of reach of children. maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qual...

Este manual também é adequado para os modelos :
Brocas e shuropopverty - 239 (301.96 kb)
Brocas e shuropopverty - 2696 (301.96 kb)
Brocas e shuropopverty - 807 (301.96 kb)
Brocas e shuropopverty - 808 (301.96 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias