Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
(3)Do not expose battery cartridge to water or rain. 6. Do not store the tool and Battery Cartridge in locations where the tempera- ture may reach or exceed 5OoC (122OF). 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because it does not have to be plugged into an electrical outlet. 2. Wear ear protectors. 3.Hold the tool firmly. 4. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 5. When driving into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Holdthe tool only by the insulated grasping surfaces to prevent electric shock if you drive into a "live" wire. SAVE THESE INSTRUCTIONS. Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Battery cartridge 1 Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the bat- Charging light tery cartridge are on the same sides as their respective markings on the fast charger. Start button Insert the cartridge fully into the port so that it rests on the charger port floor. Press the start button (red). The charging light will come on and charging will begin. lfthe charging light does not come on, press the reset button (yellow) first, then the start button (red). If the charging light goes out within 10 seconds even after pressing the reset button and start button a couple of times, the battery cartridge is dead. (CAU- TION : Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION: 0 Your new battery cartridge is not charged. You will need to charge it before use. .Do not keep the button pressed in with tape, etc. or the circuit will not function pro- perly. Also, a malfunction of the charger may result possibly causing overheating, etc. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Use only the driver bit or socket bit shown in the figure. 11 mm Do not use any other driver bit or socket (7/16") bit. 9mm (3/8") To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. Sleeve To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. NOTE : If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION: Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch to the left for clockwise rotation or to the right for counterclockwise. CAUTION : 0 Always check the direction of rotation before operation. *Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. Operation The proper fastening torque may differ depending upon the kind or size of the screw, the type of material to be fastened, etc. The relation between fasteningtorque and fastening time is shown in the figures b...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 6911D (646.26 kb)