Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
If the plug will not fi t the outlet, have a proper outlet installed by aqualifi ed electrician. WARNING Grounded Tools: Tools with Three Prong Plugs Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break FUNCTIONAL DESCRIPTION 2 3 4 1 6 7 8 5 10 11 12 9 13 14 15 16 1. Rack 2. Slide 3. Slide locking wing screw 4. Drill motor 5. Grease fitting 6. Gib adjusting screws 7. Chuck 8. Housing 9. Magnet 10. Adjusting handle 11. Cord 12. Control panel 13. Control panel socket 14. Wing screw assembly 15. Feed handle 16. Feed handle grip down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. Fig. A The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's grounding system and must never be attached to an electrically “live” terminal. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in Figure A. Double Insulated Tools: Tools with Two Prong Plugs Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association and the National Electrical Code. Double Insulated tools may be used in either of the 120 volt outlets shown in Figures B and C. Fig. B Fig. C Specifications Maximum Recommended Capacity Drill No Fine Coarse Steel Speed Motor Cat. No. Volts AC Amps Load RPM Chuck or Taper Drill Thread Tap Thread Tap Hawg™Cutters -4253- 1 • 120 6.2 600 1/2" Chuck 5/8" 5/8" - 18 3/8" - 16 - -4262- 1 120 11.5 350 3/4" Chuck 1-3/8" 1" - 14 7/8" - 9 4" ** HIGH4292-1 120 11.5 750 No. 3 M.T. 3/4" - - 2" * LOW- - - 375 - 1-1/4" 1" - 14 7/8" - 9 4" * HIGH4297-1 120 11.5 500 No. 3 M.T. 1-1/8" - - 3" * LOW- - - 250 - 1-1/2" 1" - 14 1" - 8 5" * 4 M.T. - Internal Morse Taper Socket • - 5/8" -11 or 1/2" -13 taps not **- Requires use Cat. No. 49-57-* - Requires use Arbor, Cat. No. 49-5 EXTENSION CORDS Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown to determine the required minimum wire size. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. When using more than one extension cord to ma...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 4202 (1.31 mb)
Brocas e shuropopverty - 4202 (1.31 mb)
Brocas e shuropopverty - 4206-1 (1.31 mb)
Brocas e shuropopverty - 4204-1 (1.31 mb)