Log:
Assessments - 3, GPA: 4 ( )

Instruções de Operação Black & Decker, Modelo 1190-21

Fabricante : Black & Decker
Arquivo Tamanho: 2.36 mb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Never connect this green wire to a “live” terminal. If you replace the plug on the power cord, be sure to connect the green wire only to the grounding (longest) prong on a 3-prong plug. 3 EXTENSION COii When using the tool at a considerable distance from power source,-a 3-conductor, grounding-type extension cord of adequate size must be used for safety, and to prevent loss of power and over-heating. Use the table below to-determine minimum wire size. Use only three wire extension cords which have three-prong grounding-type plugs and three-pole receptacles which accept the tool's plug. Replace or repair damaged cords. Ampere rating (on nameplate) Oto 2.0 2.10 to 3.4 3.5 to 5.0 5.10 to ’ 7.0 7.10 to 12.0 12.1 to 16.0 Ext. Cable length Wire Size (A.W.G.) 25 ft. 18 . 18 18 18 - 16 14 50 ft. 18 18 18 16 ' : 14 - 12 75 ft. 18 18 16 14 " 12 10 100 ft. 18 16 14 12 ‘^■10 150 ft. 16 14 12 12 —, .—, 200 ft. 16 14 12 10 .—, ,—. ' MOTOR Your Black & Decker tool is powered by a i & D-built motor. Be sure your power supply agrees with the nameplate marking. Volts 50/60 Hz or “AC only”, means your tool must be operated only with alternating current and never with direct current Volts DC-6GHz or AC/DC means your tool may be operated with either alternating or direct current Voltage decrease of more than 10% will cause loss of power and overheating. All B&D tools are factory tested; if this tool does not operate, check the power supply, MOTOR BRUSHES CAUTION; Disconnect tool from power source before inspection 01 servicing. Your tool uses the B&D “Checkpoint" Brush System. This insures that the tool will stop.when the'brushes wear out This prevents damage to the motor. Brushes should be regularly inspected for wear if your tool has extfrior brush inspection caps. When the cap is unscrewed, the spring and brush assembly may be withdrawn from the tool, Keep brushes clean and sliding freely in their guides. Inspection should be made every two to six months, depending upon usage, SWITCHES. Pulling the Trigger Switch turns the tool “ON”; releasing the trigger, turns the tool “OFF”, y2" drills have reversing capability. For controlling the rotational direction of the spindle, there is a slide switch built into the handle. For drilling, this switch is put in the down, “F” (forward) position. For easing drill bits out of tight holes, move the slide switch up to the “R” (reverse) position. The switch provided is a common part with other tools, ignore “Hi/Lo” marking for this tool. A built-in mechanical interlock prevents changing the direc-. tion of the tool with the Slide Switch unless the Trigger Switch is released, turning the tool “OFF” during the directional change. After any reversing, return switch to forward position. 4 SWITCHES (Continued) switch locking button and %" drills -have a switch locking button. This button permits locking the trigger in the full “ON” position for continuous operation. To lock trigger in “ON” position depr...

Este manual também é adequado para os modelos :
Brocas e shuropopverty - 1070-09 (2.36 mb)
Brocas e shuropopverty - 1070-21 (2.36 mb)
Brocas e shuropopverty - 1190-09 (2.36 mb)
Brocas e shuropopverty - 1335-09 (2.36 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias