Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Improper assembly of battery pack can cause damage to internal components. TO REMOVE BATTERY PACK • Lock sw{tch trigger on your dr{ll by p}ac{ng the direct{on of rotation se{ector {ncenter position. See Figure 4. • Locate latches on side of battery pack and depress to release battery pack from your drill See Figure 3. • Remove battery pack from your dr{ll. 11 SWITCHLOCK See Figure 4, The switch trigger can be locked in the OFF position. This feature can be used to prevent the possibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector (Forward/Reverse Selector) in center position. REVERSE SELECTORWITH CENTERLOCKPOSITION KEYLESS CHUCK See Figure 5, Your drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand. Rotate the chuck body with your other hand. The arrows on the chuck indicate which direction to rotate the chuck body in order to LOCK (tighten) or UNLOCK (release) the drill bit. UNLOCK DRILLBIT CHUCKCOLLAR FORWARD SWITCHTRIGGER Fig. 4 A WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. REVERSIBLE See Figure 4. This tool has the feature of being reversible. The direction of rotation is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction is reversed when the selector is to the right of the switch. When the selector is in center position, the switch trigger is locked. CAUTION: To prevent gear damage, always allow chuck to come to a complete stop before changing the direction of rotation. To stop, release switch trigger and allow the chuck to come to a complete stop. CHUCKJAWS LOCK (TIGHTEN) CHUCKBODY Fig. 5 _1 WARNING: Do not hold chuck body with one hand and use power of the drill to tighten chuck jaws on drill bit. Chuck body could slip in your hand or your hand could slip and come in contact with rotating drill bit. This could cause an accident resulting in serious personal injury. 12 INSTALLINGBITS See Figure 6, • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from failing out of the chuck iaws. Insert drill bit straight into chuck the full length of the jaws as shown in Figure 6. Tighten the chuck jaws on drill bit. UNLOCK DRILLBIT (RELEASE) CHUCKCOLLAR CHUCKJAWS LOCK (TIGHTEN) CHUCKBODY RIGHT Fig. 6 • To tighten the chuck jaws on drill bit; grasp and hold the collar of the chuck with one hand, while rotating the chuck body with your other hand. Note: Rotate the chuck body in the direction of the arrow marked LOCK to tighten chuck jaws. • Do not use a wrench to tighten or loosen chuck iaws. _ WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at an angle then tighten, as shown in Figure 7. This could cause drill bit to be thrown from drill, resulting in possible serious personal iniury or damage to the chuck. REMOVING BITS See Figure 0. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 4. • Loosen the chuck jaws from drill bit. • To loosen: grasp and hold the collar of the chuck with one hand, while rotating chuck body with your other hand. Note: Rotate chuck body in the direction of the arrow marked UNLOCK to loosen chuck jaws. • Do not use a wrench to tighten or loosen the chuck jaws. • Remove drill bit from chuck jaws. ADJUSTABLE TORQUE CLUTCH Your drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. TO ADJUST TORQUE • Identify the twenty four position torque indicator settings located on the front of your drill. See Figure 8. • Rotate adjusting ring to the desired setting. • 1-4 For driving small screws. • 5-8 For driving screws into soft material. • 9-12 For driving screws into soft and hard materials. • 13-16 For driving screws in hard wood. • 17-20 For driving large screws. • 21-_.1 For heavy drilling. ADJUSTING RING TO DECREASE TORQUE TO INCREASE TORQUE Fig. 8 Fig. 7 13 BIT STORAGE See Figure 9, When not in use, bits provided with your drill can be placed in the storage area located on the bottom of your drill as shown in Figure 9. SCREWDRIVERBITS BIT STORAGEAREA L Fig. 9 _i WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING See Figu...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 315.11521 (1.11 mb)