Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
• Do not expose charger to rain, snow in charger DG111800CH and two (2) to dropped, or otherwise damaged. or frost. (4) hours in the fast charger Take it to a qualified serviceman. DG151800CH. • Do not incinerate battery pack. It • Do not disassemble charger or COLOCACAO DE PARAFUSOS can explode in a fire. battery pack. Take it to a qualified CHARGING Connect the current carrying prongs AUTO-ATARRAXADORES 1. Perfure um orificio-piloto de Length of Cord in Feet 25 50 100 Minimum Wire Size (AWG) of Extension Cord for 150 AWG Size of Cord 18 18 18 16 on the power cord to a 120V AC 60Hz tamanho correto segundo as wall outlet. Connect the other end of recomendacoes do fabricante do the power cord to the battery pack. If parafuso para a fixacao que esta the charger is equipped with an LED, a sendo usada. red light will light up as long as the 26 Pg Operating Instructions and Parts Manual Charging Battery (Cont’d.) battery pack is connected to the charger and the charger is plugged in. With normal use, the battery pack will be fully charged after about three (3) to six (6) hours with charger DG111800CH and one (1) to two (2) hours with fast charger DG151800CH. The fast charge battery DG151800BP will charge in either charger. The battery DG111800BP will charge only in charger DG111800CH. Disconnect charger from power source when not in use. IMPORTANT: THE BATTERY PACK SHOULD NOT BE LEFT ON THE CHARGER FOR MORE THAN FORTYEIGHT (48) HOURS. Operation VARIABLE-SPEED TRIGGER SWITCH (some models) If your Drill/Driver is equipped with a variable-speed trigger switch, the pressure you apply to the trigger controls the tool speed. Apply more pressure to increase the speed and release pressure to decrease speed. This accurate speed control allows you to drill without center-punching and to use the Drill/Driver as a power screwdriver. Bits are available for driving screws as well as running bolts and nuts. FORWARD/REVERSE BUTTON This Drill/Driver is equipped with a forward/reverse lever which is used to change the rotation of the chuck. Do not attempt to change the rotation unless the chuck is completely stopped. Moving the NOTICE Forward/Reverse Button while chuck is rotating can damage the tool. For forward rotation, firmly press in on the lever marked FWD. For reverse rotation, firmly press in on the lever marked REV. TRIGGER LOCK To activate trigger lock, move the forward/reverse lever so it is centered in the handle. GEAR SHIFTING (DG151800CK only) The DG151800CK Drill/Driver is equipped with two separate gear ranges, low and high. Low gear provides high-torque and slower drilling speeds for heavy duty work or for driving screws. High gear provides faster speeds for drilling lighter work. To change speeds, slide switch to the high or low position. Actuate trigger slightly if the gear shift does not fully engage. Note: If Drill/Driver is running, but the chuck will not turn, check to make sure the gear shifting switch is pushed fully into desired setting. ADJUSTABLE CLUTCH This Drill/Driver features 16 clutch settings. Output torque will increase as the clutch ring is rotated from 1 to 16. 1 to 2 for driving small screws. 3 to 4 for driving screws into soft materials or plastics. 5 to 7 for driving screws into softwoods. 8 to 10 for medium woods. 11 to 14 for driving screws into medium / hard woods. 15 to 16 for driving screws into metal. The “drill” position locks up the clutch to permit heavy-duty drilling and driving work. It also allows bits to be changed quickly and easily in the keyless chuck. INSERTING BITS Move Forward/Reverse Button to the center “Off” position. Remove battery pack (See “Charging Battery” section) and rotate the clutch ring to the drill bit symbol. Rotate the chuck sleeve counterclockwise (viewing from chuck end), and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small bits, or as far as it will go for large bits. Close chuck by rotating the chuck sleeve clockwise and securely tighten by hand. Do not use the ! CAUTION power of the drill to loosen or tighten bit while holding chuck. The spinning chuck will cause friction burn or hand injury. REMOVING CHUCK Remove battery pack. Rotate clutch ring to drill bit symbol and open chuck all the way. Turn left-hand-threaded screw inside chuck clockwise, and remove it . Insert the short arm of a 3/8" hex key wrench and close jaws on flats of wrench. Strike long arm of wrench sharply counterclockwise, remove wrench and unthread chuck from spindle. INSTALLING CHUCK To install chuck, reverse “Removing Chuck” procedure. Always keep the 4 spindle threads, chuck threads, and securing screw free of debris. GENERAL DRILLING The front end of ! WARNING the Drill/Driver may be made “live” if the tool drills into live wiring in the wall. TO PREVENT ACCIDENTAL ELECTRICAL SHOCK, HOLD DRILL/DRIVER ONLY BY THE SOFT GRIP HANDLE. ! WARNING Safety glasses must be worn during operation. 1. Set ...
Este manual também é adequado para os modelos :Brocas e shuropopverty - DG111800CD (234.49 kb)