Assessments - 4, GPA: 4 ( )

Fabricante : Milwaukee Arquivo Tamanho: 266.12 kb Arquivo Nome : Língua de Ensino:

Others may be hazardous. WARNING! Removing and Replacing Quik-Lok ® Cords (Fig. 1) MILWAUKEE's exclusive Quik-Lok ® Cords provide instant field replacement or substitution. To prevent personal injury, remove the chuck key from the chuck after each use. WARNING! Installing Bits into Keyed Chucks (Fig. Cat. No. 0234-1, 0244-1 Fig. 3 Tighten Loosen Fig. 1 1. To remove the Quik-Lok ® Cord, turn the cord nut 1/4 turn to the left and pull it out. 2. To replace the Quik-Lok ® Cord, align the connector keyways and push the connector in as far as it will go. Turn the cord nut 1/4 turn to the right to lock. Installing Side Handle (Fig. 2) MILWAUKEE Magnum Drills are supplied with a side handle that can be installed on either side of the tool for right or left handed use. To install the side handle, thread it into the socket on the desired side of the tool and tighten it securely. Always use the side handle for best control. Fig. 2 1. Open the chuck jaws wide enough to insert the bit. Be sure the bit shank and chuck jaws are clean. Dirt particles may prevent the bit from lining up properly. 2. When using drill bits, insert the bit into the chuck. Center the bit in the chuck jaws and lift it about 1/16" off of the bottom. Tighten the chuck jaws by hand to align the bit. When using screwdriver bits, insert the bit far enough for the chuck jaws to grip the bit shank. Tighten the chuck jaws by hand to align the bit. 3. Place the chuck key in each of the three holes in the chuck, turning it clockwise as shown. Tighten securely. 4. To remove the bit, insert the chuck key into one of the holes in the chuck and turn it counterclockwise. 6 7 Fig. 5 Fig. 5 Installing Bits into Keyless Chucks (Fig. 4) Cat. No. 0233-20 These tools are equipped with a hand-tightening keyless chuck. Always unplug the tool before installing or removing bits. To reduce the risk of • Do not grasp the bit while thechuck is rotating or while thebit is falling from the chuck. • Release the trigger as soon asthe ratcheting stops to avoidthrowing the bit. WARNING! the front of the NOTE: Attaching the drill the chuck from side marked “LOW” right hand thread making by 1/3, or 33%. Attaching the drill chuck the chuck by hand. to the opposite side increases by 50%. NOTE: When replacing the chuck, replace the left hand thread 3. When assembled, turn the Right Angle chuck. Drive head to the desired position tighten the clamping screws to secure the unit. Thread the chuck onto the Right Angle Drive spindle (5). INSTALL CHUCK LOCKING SCREW. Removing the Chuck From Right Fig. 6 Sleeve To close Angle Drive Unit (Fig. 9) NOTE: If the spindle rotates when opening Fig. 9 or closing the chuck jaws, grasp the chuck The chuck can be removed from the Right and slightly rotate back and forth to en- Angle Drive Unit in the same manner it is 1. To open the chuck jaws, turn the sleeve gage the spindle-lock mechanism. removed from the drill; however, ALWAYS in the counterclockwise direction. REMOVE RIGHTANGLE DRIVE FROM THE The spindle will remain locked until the tool When using drill bits, allow the bit to Fig. 8 1 2 3 4 5 DRILL BEFORE ATTEMPTING TO LOOSEN is turned on. The spindle-lock mechanism strike the bottom of the chuck. Center THE CHUCK. This will prevent damaging will automatically disengage when the tool the bit in the chuck jaws and lift it about the drill's gearing. Use the open end wrench is turned on. 1/16" off of the bottom. provided to hold the Right Angle Drive When using screwdriver bits, insert the WARNING! To reduce the risk of injury, al-ways wear eye protection. spindle before attempting to loosen the bit far enough for the chuck jaws to chuck. grip the hex of the bit. 2. To close the chuck jaws, hold the collar while turning the sleeve in the clockwise direction. Tighten securely. Chuck Removal (Fig. 7) Installing Bits into Keyless Chucks This tool is equipped with a threaded spindle (Fig. 5 & 6) Cat. No. 0235-21 to hold the chuck. Before removing the 1. Remove the chuck from the drill follow- These tools are equipped with a spindle- chuck, unplug the tool and open the chuck ing instructions (See “Removing the lock mechanism and a single-sleeve key- jaws. A left-handed thread screw is lo- Chuck From the Drill”). Slip the double less chuck. Always unplug the tool before...

Baixe o seu

Para fazer o download, introduza 2 dígitos :