Assessments - 3, GPA: 3.7 ( )

Fabricante : Milwaukee Arquivo Tamanho: 416.12 kb Arquivo Nome : Língua de Ensino:

page 2 FUNCTIONAL DESCRIPTION 1. Drive shank 2. Forward/reverse switch (Cat. No. 9072-20, 9072-22, 9092-20, 9096-20) 3. Trigger (Cat. No. 9072-20, 9072-22, 9092-20, 9096-20) Rocker switch (Cat. No. 9070-20, 9071-20, 9075-20) 4. Speed control dial (Cat. No. 9072-20, 9072-22, 9092-20, 9096-20) 5. Quik-Lok® cord (Cat. No. 9072-20, 9072-22, 9092-20, 9096-20) 6. Quick change chuck (Cat. No. 9092-20, 9096-20) 7. Tool hanger (Cat. No. 9092-20, 9096-20) 8. Tool hanger ring (Cat. No. 9092-20, 9096-20) 1 4 3 2 Cat. No. 9072-20 9072-22 5 6 Cat. No. 9092-20 7 8 3 Cat. No. 9075-20 Symbology Specifications Double Insulated Volts Alternating Current/ Direct Current Volts Alternating Current Amperes Impacts per Minute Under Load (IPM) Underwriters Laboratories, Inc. Canadian Standards Association Mexican Approvals Marking Cat. No. Volts A No Load RPM Drive Shank Impacts Per Minute Average Torque Output 9070-20 9071-20 9072-20 9072-22 9075-20 9092-20 9096-20 120 AC/DC 120 AC/DC 120 AC Only 120 AC Only 120 AC/DC 120 AC Only 120 AC Only 7 7 7 7 7 7 7 1800 1800 600-1800 600-1800 1750 600-1800 600-1800 1/2" 1/2" 1/2" 1/2" 3/4" 7/16" Hex 5/8" Hex 2600 2600 1000-2600 1000-2600 2500 1000-2600 1000-2600 300 ft-lbs. 300 ft-lbs. 100-300 ft-lbs. 100-300 ft-lbs. 380 ft-lbs. 100-315 ft-lbs. 100-315 ft-lbs. Quick Change Chuck Capacities* Cat. No. Quick Change Auger Bits Selfeed Bits 9070-20 1-1/2" 2-9/16" 9072-20 1-1/2" 2-9/16" 9072-22 1-1/2" 2-9/16" 9092-20 1-1/2" 2-9/16" 9096-20 1-1/2" 2-9/16" * Only for use with the 7/16" or 5/8" Hex Quick Change chuck, standard equiptment on the 9092-20 (7/16") and 9096-20 (5/8"), optional accessory (Cat. No. 48-66-0061) on other models. page 3 GROUNDING EXTENSION CORDS Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have it repaired by a MILWAUKEE service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualifi ed electrician. WARNING Grounded Tools: Tools with Three Prong Plugs Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's grounding system and must never be attached to an electrically “live” terminal. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in Figure A. Double Insulated Tools: Tools with Two Prong Plugs Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association and the National Electrical Code. Double Insulated tools may be used in either of the 120 volt outlets shown in Figures Fig. B Fig. C B and C. Fig. A Grounded tools require a three wire extension cord. Double insulated tools can use either a two or ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :