Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
They can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. Charging the Power Pack THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS. The drills covered in this instruction manual use the same charger. The 16 hour charger is designed to use standard household 120 volt 60 Hz power. 2 2 1. Put the switch control lever in the center OFF position (Fig. 1) and remove power pack from the tool. 2. Plug the charger into any standard 120 Volts 60 Hz electrical outlet. 3. Insert the power pack into the charger and let it charge for 16 hours. 4. Remove pack from the charger and replace in tool. Important Charging Notes 1. After normal usage, your drill should be fully charged in 16 hours or less. Your drill was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 16 hours. 2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is important and will prevent serious damage to the power pack. Longest life and best performance can be obtained if the power pack is charged when the air temperature is about 75°F. 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the power pack and charger to your local Black & Decker service center. See "Tools Electric" in yellow pages. 5. The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using drill with its power pack in a depleted condition. 6. To prolong power pack life, avoid leaving the power pack on charge for more than 8 hours. Although overcharging is not a safety concern, it can significantly reduce overall power pack life. 7. When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicating that there is contact between the battery and charger. The light will stay on as long as the battery is in the charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a different color when the charging cycle is complete. Safety Warnings and Instructions: Drills 1. Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch. 2. Hold drill firmly to control the twisting action of the drill. See figure 2. 3. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall.Grip the drill firmly to control the twisting action (see Fig.2) and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. Operating Instructions Switch and Control Button A forward/reverse control button determines the direction of the tool and also serves as a lock off button (Fig. 1 or 1A). To select forward rotation, release the trigger switch and depress the forward/reverse control button as shown in Figure 1 or 1A. To select reverse, depress the forward/reverse control button the opposite direction. The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. NOTE: The first time tool is run after changing direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem. Torque Control (Catalog Number CD9600) To set the tool’s torque, rotate the adjustable torque collar clockwise as required. 6 positions are marked around the collar and the higher the number, the higher the torque. Each click in a clockwise direction means an increase in the torque produced. Position 6 is the drill mode and is marked with the picture of a drill bit. In this position the clutch will not operate. This permits heavy duty drilling / driving screws. Torque Control (Catalog Numbers CD1200, CD1440, CD1800) To set the tool’s torque,...
Este manual também é adequado para os modelos :Brocas e shuropopverty - CD1200 (158.5 kb)