Assessments - 4, GPA: 5
(
)
)
|
Facilidade de uso
SAVE THIS MANUAL FOR FUTURE REFERENCE. OPERATING INSTRUCTIONS Switch and Control Button A forward/reverse control button determines the direction of the tool and also serves as a lock off button (Fig. A). To select forward rotation, release the trigger switch and depress the forward/reverse control button as shown in Figure A. To select reverse, depress the forward/reverse control button the opposite direction. The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. NOTE: The first time tool is run after changing direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem. Torque Control This tool is fitted with a collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials. • For drilling in wood, metal and plastics, set the collar to the drilling position symbol . • For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows: • Set the collar to the lowest torque setting. • Tighten the first screw. • If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws. Keyless Chuck Operation To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end. Drilling • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the drill firmly to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole This will help reduce jamming. • Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. Lubricants that work best are sulphurized cutting oil or lard oil. • When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear chips from the flutes. • Make sure switch turns drill on and off. WARNING: It is important to support work properly and to hold the drill firmly to prevent loss of control which could cause personal injury If you have questions on how to operate tool, call: 1-800-54-HOW-TO (544-6986). DRILLING IN WOOD Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes. DRILLING IN METAL Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil. DRILLING IN MASONRY Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate. TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Battery not charged. • Check battery charging requirements. • Battery will not charge. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Check current at receptacle by plugging in a lamp or other appliance. • Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. • Surrounding air temperature • Move charger and tool to a too hot or too cold. surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the...