Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Fig. 12 TO RETIGHTEN A LOOSE CHUCK The chuck may become loose on the spindle and develop a wobble. To tighten, follow these steps: • Unplug your drill. ,_ WARNING: Failure to unplug your drill could result in accidental starting causing serious; injury. • Open the chuck jaws. • Insert hex key wrench into chuck and tighten chuck jaws securely. Tap hex key wrench sharply with a mallet in a clockwise direction. This will tighten the chuck on the spindle. • Open the chuck jaws and remove the hex key wrench. • Tighten the chuck screw. Note: The chuck screw has left hand threads. Fig. 11 11 I 1]=1 GENERAL All parts represent an important part of the double insulation system and should be serviced only at a Sears Service Center. Avoid using solvents when cleaning plastic pads. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. ,_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic pads. They contain chemicals that can damage, weaken or destroy plastic. It has been found that electric tools are subject to accelerated wear and possible premature failure when they are used on fiberglass boats, sports cars, wallboard, spackling compounds, or plaster. The chips and grindings frem these materials are highly abrasive to electric tool pads, such as bearings, brushes, commutators, etc. Consequently, it is not recommended that this toot be used for extended work on any fiberglass material, wallboard, spackling compounds, or piaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jet. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. ,_ WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. DOUBLEINSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. IMPORTANT Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest Sears Service Center for repair. Always use original factory replacement parts when servicing. EXTENSION CORDS The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent tool overheating, use an extension cord that is heavy enough to carry the current the tool will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. When working outdoors, use an extension cord that is suitable for outdoor use. The cord's jacket will be marked WA. ,_IL CAUTION: Keep extension cords away from the drilling area and position the cord so that it will not get caught on lumber, tools, etc., during drilling operation. _ll WARNING: Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. Extension cords suitable for use with your drill are available at your nearest Sears Retail Store. 12 ThefollowingrecommendedaccessoriesarecurrentlyavailableatSearsretailstores. • HighSpeedBits(Forwoodor metal).........1/2in.Max. • DowelingJig (ItemNo.9-4186) Bits............................................... • Masonry3/4in.Max. • Drill Stand (Item No. _-25989) • WoodBoringBits...........................................• Wire Brushes, All 1in.Max. • HoleSaws..................................................... 2 in.Max. WARNING: The use of attachments or accessories not listed might be hazardous. WARRANTY FULL ONE YEAR WARRANTY ON CRAFTSMAN PROFESSIONAL DRILL-DRIVER If this tRAFT$MRN Drill-Driver fails due toa defect in material or workmanship within one year from the date of pur chase, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 SAVE THESE INSTRUCTIONS 13 14 CRAFTSMAN 318 in. PROFESSIONAL DRILL-DRIVER MODEL NO. 315.279440 IThe model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 3...