Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
4 RULES FOR SAFE OPERATION (Continued) • An extension cord should not be used unless • absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and c. That wire size is large enough for AC ampere rating of charger as specified below: Cord Length (Feet) 25' 50' 100' Cord Size (AWG) 16 16 16 Note: AWG = American Wire Gage DO NOT OPERATE CHARGER WITH A DAMAGED CORD OR PLUG. If damaged, have replaced immediately by a qualified serviceman. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. To reduce risk of electdc shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Do not use charger outdoors. Disconnect charger from power supply when not in use. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. ,_ Look for this symbol to point out important safety precautions. It means attention!H Your safety is involved. IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your drill-driver continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the yellow and green lights on your battery charger to come on instead of the red light. The yellow and green lights indicate soft start mode and will switch to green only, indicating slow charge mode. The red light indicates fast charge mode, 1 hour charge time. The green light indicates slow charge mode, requiring overnight charging for batteries to reach full charge. If the green light comes on after letting battery pack cool down, remove it from charger for additional cooling. Once the battery pack cools down, you can recharge battery pack in fast charge mode as normal. Do not leave a hot battery pack in charger until it cools down. The green light will not go off when battery pack cools. If fast charge mode is desired, you must physically remove a hot battery pack from the charger, let it cool, then place it back in charger after it has cooled down. Note: This situation only occurs when continuous use of your drill causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING YOUR DRILL-DRIVER" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears repair center for electrical check. ,_ WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears Retail Stores. Thefollowingrecommendedaccessoriesarecurrentlyavailableat SearsRetailStores. • 6-Pc.ExtraLengthMagnitePowerBitSet • HighSpeedBits(ForWoodorMetal)..3/4in.Max. • 30-Pc.PowerScrewdriver/Nutdriver• SetandCase KeylessChuck(ItemNo.9-20988) • 17-Pc.PowerScrewdriver/Nutdriver SetandCase ,_ WARNING: The use of attachments or accessories not listed might be hazardous. KNOW YOUR DRILL-DRIVER WRIST STRAP See Figure 1, See Figure 1. Before attempting to use any tool familiarize yourself A wrist strap is provided to reduce the chances of with all operating features and safety requirements. dropping your drill-driver. Place one hand through the wrist strap when carrying tool. "flNO-SPEED BIT STORAGE LEVEL BATTERYPACK GEARTRAIN (HI-LO) KEYLESSCHUCK SELECTOR YELLOWAND GREENLIGHTS INDICATESOFTSTARTMODE SWITCH GREENLIGHT "ON" TRIGGER INDICATESSLOWCHARGING MODEOR FULLYCHARGED i MODE WRIST STRAP BATTERY CHARGER _ SCREWDRIVERBITS Fig. 1 ,_ WARNING: If any parts are missing, do not operate so could result in possible serious personal injury. tool until the missing parts are replaced. Failure to do _ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. ,_ WARNING: Do not allow familiarity with your drill-driver to make you careless. Remember that a careless fraction of a second is sufficient to inflictsevere inju...