Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
The drilling direction is reversed when the selector is to the right of the switch. When the selector is in center position, the switch trigger is locked. SELECTOR REVERSE CENTERPOSITION (LOCK) SWITCH f TRIGGER FORWARD Fig. 3 CAUTION: To prevent gear damage, always allow chuck to come to a complete stop before changing the direction of rotation. To stop, release switch trigger and allow the chuck to come to a complete stop. TO INSTALL BATTERY PACK See Figure 4. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Place battery pack in your drill. Align raised rib inside drill with groove on battery pack, See Figure 4. BATTERYPACK t LATCHES DEPRESSLATCHESTO RELEASEBATTERYPACK Fig. 4 Make sure the latches on each side of your battery pack snap in place and battery pack is secured in drill before beginning operation. _ CAUTION: When placing battery pack in your drill, be sure raised rib inside drill aligns with groove on battery pack and latches snap into place properly. Improper assembly of battery pack can cause damage to internal components. TO REMOVE BATTERY PACK • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Locate latches on end of battery pack and depress to release battery pack from your drill. See Figure 4. • Remove battery pack from your drill. KEYLESSCHUCK See Figure 5. Your new drill has a keyless chuck. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and holdthe collar of the chuck with one hand. Rotate the chuck body with your other hand. The arrowson the chuck indicatewhich direction to rotate the chuck body in order to LOCK (tighten) or UNLOCK (release) the drill bit. UNLOCK CHUCK (RELEASE) BODY INSTALLING BITS See Figure 7. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Al_,o, raise the front of your drill slightly to keep the bit from falling out of the chuck jaws. • Insert drill bit into chuck the full length of the jaws as shown in figure 7. CHUCKJAWS CHUCKBODY DRILLBIT LOCK (_ (TIGHTEN) CHUCK COLLAR Fig. 5 ,_ WARNING: Do not hold chuck body with one hand and use power of the drill to tighten chuck jaws on drill bits. Chuck body could slip in your hand or your hand could slip and come in contact with rotating drill bit. This could cause an accident resulting in serious personal injury. BIT STORAGE See Figure 6. When not in use, bits provided with your drill can be placed in the storage area located on the top of your drill as shown in figure 6. SCREWDRIVER BITS AREA DRILLBIT CHUCKCOLLAR RIGHT Fig. 7 • Tighten the chuck jaws on drill bit. • To tighten the chuck jaws on drill bit; grasp and hold the collar of the chuck with one hand, while rotating the chuck body with your other hand. Note: Rotate the chuck body in the direction of the arrow marked LOCK to tighten chuck jaws. • Do not use a wrench to tighten or loosen the chuck jaws. ,_i WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at an angle and then tighten, as shown in figure 8. This could cause drill bit to be thrown from drill, resulting in possible serious personal injury or damage to the chuck. Fig, 6 Fig. 8 9 REMOVING BITS See Figure 7. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Loosen the chuck jaws from drill bit. • To loosen: grasp and hold the collar of the chuck with one hand, while rotating chuck body with your other hand. Note: Rotate chuck body in the direction of the arrow marked UNLOCK to loosen chuck jaws. • Do not use a wrench to tighten or loosen the chuck jaws. • Remove drill bit from chuck jaws. ADJUSTABLE TORQUE CLUTCH See Figure9. Your drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. The proper setting depends on the type of material and the size of screw you are using. TO ADJUST TORQUE • Identify the twenty four torque indicator settings located on the front of your drill. See Figure 9. • Rotate adjusting ring to the desired setting. • 1 -4 For driving small screws. • 5 -8 For driving screws into soft material. • 9 -12 For driving screws into soft and hard materials. • 13 -16 For driving screws in hard wood. • 17 -20 For driving large screws. • 21 -,11 For heavy ddlling. TO DECREASE TORQUE ADJUSTING RING ,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. LEVEL DRILLING See Figure 10. A convenient feature provided with your drill is a level. It is recessed in the motor housing on top of your drill. It can be used to k...