Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
See the table below for recommendations when using common screw sizes. Driving Self-tapping Screws In addition to the guidelines given in the General Driving Instructions, the following also apply: • Prior to driving the self-tapping screw in place, drill a pilot hole of the recommended size by the manufacturer. Place the tip of the screw in the pre-drilled hole and while gently holding the screw square, slowly start driving the screw. Once it has properly started, discontinue holding the screw threads and finish driving the screw. As soon as the screw is seated, release the switch trigger and lift the drill from the screw head. Driving Machine Screws In addition to the guidelines given in the General Driving Instructions, the following also apply: • Prior to driving the machine screw in place, drill and tap a hole of the recommended size by the manufacturer. Start the threads of the screw in the tapped hole by hand and once squarely in place, discontinue holding the screw and then start to slowly drive the screw with the driver. Once the screw has been fully seated, release the switch trigger and lift the drill from the screw head. RECOMMENDATIONS FOR DRIVING WOOD SCREWS SCREW SIZE PILOT DRILL DIAMETER (FOR SOFT WOOD) (FOR HARD WOOD) SHANK PILOT HOLE SCREWDRIVER BIT TIP SLOTTED BIT PHILLIPS BIT #6 #8 #10 #12 1/16" (0.063") 5/64" (0.078") 3/32" (0.094") 7/32" 0.219") 5/64" (0.078") 3/32" (0.094") 7/64" (0.109") 1/8" (0.125") 9/64" (0.141") 11/64" (0.172") 3/16" (0.188") 7/32" (0.219") 3/16" 1/4" 5/16" 3/8" #2 #2 #2 OR #3* #3 * Some head styles in this size take a #2 Phillips bit and others #3. 8 DG201800CD DG201800CD Removing Screws In order to remove a screw from a workpiece, use the following steps: • Set the clutch adjusting collar to its highest setting and set the speed selector to its lowest "1" setting. • Install the proper screwdriver bit into the drill’s chuck. • Fully depress the REV button. • Place the screwdriver bit in the screw head and with enough pressure exerted on the drill so that it doesn’t jump out of the screw head, start the drill to remove the screw. Maintenance Cleaning All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could dissolve or otherwise damage the material. Failure to Start Should your tool fail to start, make sure the battery pack is charged and installed in the drill. Battery Service The battery pack supplied with this drill will self-discharge and lose some of its capacity over time. Therefore, if it is stored unused for a long period of time, then it may require recharging before use. In order to get the most out of your batteries, it is recommended that the pack be recharged every 2-3 months and when doing so, remove the pack from the charger after 2-3 hours of charging. Removing/Replacing the Chuck If there is a need to replace the chuck, use the following steps to do so: • Remove the battery pack from the drill. • Rotate the clutch collar until its drill bit symbol aligns with the arrow on the top of the drill housing. • Open the chuck jaws fully by unscrewing the chuck sleeve counterclockwise (when viewing the chuck from its end). • Locate the left-handed screw inside the chuck and with the proper screwdriver bit and remove this screw by turning it clockwise. • Insert the short arm of a 3/8" hex key or Allen wrench into the chuck and tighten the jaws of the chuck on the flats of this wrench. • With a hammer or the like, strike the long arm of the wrench sharply so that the chuck will turn counterclockwise. • Once the chuck has been loosened, remove the wrench and unscrew the chuck from its spindle. • To replace the chuck with another one, reverse the steps noted above. Always keep the spindle threads, chuck threads, and securing screw free of debris. Service Tool service must be performed only by qualified repair personnel and by an AUTHORIZED SERVICE CENTER. Service or maintenance performed by unqualified personnel could result in a risk of injury. For information regarding the operation or repair of this product, please call 1-800- 424-8936. For Replacement Parts or Technical Assistance, call 1-800-424-8936 Part Description Number Charger – 18V DG024700AV Battery Pack – 18V DG024900AV Chuck – 3/8" DG029900AV Set Screw SX173400AV Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list Address any correspondence to: Campbell Hausfeld Attn: Parts Department 100 Production Drive Harrison, OH 45030 U.S.A. 9 Operating Instructions Operating Instructions 1. DURATION: One (1) Year from the date of purchase by the original purchaser on drill. Batteries are warranted for one (1) year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 424-8936 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Cam...