Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, THE EXHAUST PORT MUST BE COVERED WITH A TOWEL before applying air pressure. FAILURE TO COVER THE EXHAUST PORT CAN RESULT IN SERIOUS INJURY. 4. Connect the impact wrench to the air supply and cover the exhaust port with a towel. Run the impact wrench in both the forward and reverse directions for 20 to 30 seconds. Oil will discharge from the exhaust port when air pressure is applied. Impact Mech anism Lu bric ati on Lubricate the impact mechanism monthly. Disconnect the impact wrench from the air supply before lubricating. 1. Disconnect the impact wrench from the air supply. 2. Remove the slotted screw or allen head screw from the oil port hole. 3. Squeeze approximately 1 oz. of air tool oil in the oil port hole. Replace the screw. 4. Reconnect the air supply to the impact wrench and run for 20 to 30 seconds. Lubricate the entire impact mechanism by rotating the tool upside down and sideways while running the tool. 5. Remove the screw and hold the oil port hole over a suitable container to allow excess oil to drain. Sometimes triggering the tool when dumping the oils helps to force out the excess oil. 6. If the oil is dirty, repeat the procedure above until the oil comes out clear. Install the screw and tighten. The residual oil remaining in the impact mechanism chamber is all that is needed for proper lubrication. Rec omme nded Hooku p The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Regulator Lubricator Filter 60 psi Min. 90 psi Max. O CO2 90 psi Important Safety Instructions (Continued) Tl0502 opEraTInG InsTrUCTIons (Continued) 2 . An oiler can be used to provide oil circulation through the tool A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool 3 . Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 200 psi, whichever is greater Use 1/4 inch air hose for runs up to 50 feet Use 3/8 inch air hoses for 50 foot run or longer 200 psi or greater 3/8 inch I D 4 . Use a pressure regulator on the compressor, with an operating pressure of 0 psi -125 psi A pressure regulator is required to control the operating pressure of the tool between 60 psi and 90 psi rEGUlaTor opEraTIon This impact wrench is equipped with several power (speed) settings Use the switch on the rear of the tool to select the proper setting before operating tool The tool has 3 forward settings and 1 reverse setting Do not change settings while tool is running spEED aDJUsTMEnT An impact wrench should never be used to set torque Use a torque wrench to set the torque To remove lugs or bolts, set the regulator to the maximum setting When installing, always use a torque wrench to attain the proper torque of the lugs or bolts When reassembling be careful not to overtighten. Bolts may fail or cause a hazardous condition. Be sure to set the regulator to the minimum setting then use a torque wrench to set torque. noTE: It is not recommended to install a quick coupler between the tool and the whip hose Using fittings or air hoses which are too small can create a pressure drop and reduce the power of the tool For 3/8, 1/2 and 3/4 inch impact wrenches use 3/8 inch (I D ) fittings with 1/4 inch NPT threads Most compressors are shipped with a short, 1/4 inch I D hose For proper performance and more convenience, use a 3/8 inch I D hose Hoses longer than 50 feet should have a 1/2 inch I D Never carry a tool by the hose or pull the hose to move the tool or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. UsEr-MaInTEnanCE InsTrUCTIons TECHnICal sErvICE Please call our Tool Hotline at 1-800543- 6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual rEplaCEMEnT parTs InforMaTIon For information regarding where to order replacement parts, call toll free 1-800-543-8622 Please provide the following information: • Model number • Stamped-in code • Part number and description Tool rEpaIr Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently assEMblY proCEDUrE for sEals When repairing a tool, the internal parts must be cleaned and lubricated Parker O-lube or equivalent must be used on all o-rings Each o-ring must be coated with O-lube before assembling A small amount of oil must be used on all moving surfaces and pivots After reassembling, a few...