Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
F FF O OO R RR W WW A AA R RR D DD / // R RR E EE V VV E EE R RR S SS E EE A AA N NN D DD T TT R RR I II G GG G GG E EE R RR L LL O OO C CC K KK L LL E EE V VV E EE R RR B BB e ee s ss u uu r rr e ee t tt h hh e ee t tt r rr i ii g gg g gg e ee r rr i ii s ss r rr e ee l ll e ee a aa s ss e ee d dd w ww h hh e ee n nn c cc h hh a aa n nn g gg i ii n nn g gg t tt h hh e ee p pp o oo s ss i ii t tt i ii o oo n nn o oo f ff t tt h hh e ee l ll e ee v vv e ee r rr . .. Always store the tool in the “ ““ L LL O OO C CC K KK E EE D DD / // O OO F FF F FF ” ”” position. A AA l ll w ww a aa y yy s ss c cc h hh e ee c cc k kk t tt h hh e ee d dd i ii r rr e ee c cc t tt i ii o oo n nn o oo f ff t tt h hh e ee C CC o oo r rr d dd l ll e ee s ss s ss D DD r rr i ii l ll l ll ' '' s ss r rr o oo t tt a aa t tt i ii o oo n nn b bb e ee f ff o oo r rr e ee u uu s ss e ee . .. T TTO OO S SSE EEL LLE EEC CCT TT T TTH HHE EE D DDI IIR RRE EEC CCT TTI IIO OON NNS SS O OOF FF R RRO OOT TTA AAT TTI IIO OON NN: :: • To select forward Cordless Drill rotation, press the trigger lock from left to right flat against the Cordless Drill body. • To select reverse, press the trigger lock lever in the opposite direction. • The center position locks TRIGGER LOCK FORWARD LOCK REVERSE SSCCRREEWWDDRRIIVVIINNGGTTOORRQQUUEE SSEETTTTIINNGGSS T TTo oo p ppr rre eev vve een nnt tt d dda aam mma aag ggi iin nng gg t tth hhe ee t tto ooo ool ll o oor rr d ddr rri iiv vvi iin nng gg s ssc ccr rre eew ww t tto ooo oo d dde eee eep pp i iin nnt tto oo w wwo oor rrk kk p ppi iie eec cce ee, ,, r rre eel lle eea aas sse ee t tth hhe ee t ttr rri iig ggg gge eer rr w wwh hhe een nn y yyo oou uu f ffe eee eel ll t tth hhe ee c ccl llu uut ttc cch hh s ssl lli iip pp. .. CONTROL RING T TTH HHE EE C CCO OON NNT TTR RRO OOL LL R RRI IIN NNG GG A AAD DDJ JJU UUS SST TTS SS T TTH HHE EE L LLE EEV VVE EEL LL O OOF FF T TTO OOR RRQ QQU UUE EE: :: • For light duty work, use lower settings. • For heavy duty work, use higher settings. P PPR RRO OOP PPE EER RR S SSE EET TTT TTI IIN NNG GG F FFO OOR RR D DDR RRI IIV VVI IIN NNG GG S SSC CCR RRE EEW WWS SS: :: 1. Set the ring on the lowest setting to begin. 2. Try tightening the first screw. If the drill drives smoothly, proceed with the next screw. 3. If the Drill’s clutch slips, increase the torque setting and try again until the Drill drives the screw without incident. HHIIGGHH // LLOOWW SSPPEEEEDD (( GGEEAARR)) SSHHIIFFTTIINNGG F FFO OOR RR L LLO OOW WW S SSP PPE EEE EED DD S SSE EET TTT TTI IIN NNG GG: :: • Slide the switch on top of the Drill to Position 1 for high torque applications and driving screws. F FFO OOR RR H HHI IIG GGH HH S SSP PPE EEE EED DD S SSE EET TTT TTI IIN NNG GG: :: • Slide the switch to Position 2 for light duty projects. LOW SPEED HIGH SPEED 15 W WWH HHE EEN NN D DDR RRI IIV VVI IIN NNG GG F FFA AAS SST TTE EEN NNE EER RRS SS: :: • Always start slowly and gradually increase the speed of the Drill. • Release the trigger when you feel the clutch slip. • Always keep the driver bit straight to prevent damage to the screw. • Hold the Drill with both hands to ensure control if the bit should stick or slip. • To prevent wood from splitting, drill pilot holes into the wood before driving in the screws. DDRRIILLLLIINNGG MMEETTAALL W WWH HHE EEN NN D DDR RRI IIL LLL LLI IIN NNG GG H HHA AAR RRD DD M MME EET TTA AAL LLS SS: :: • Apply a lubricant, such as cutting oil, to the tip of the bit. • Start with a small hole then enlarge to the required size. Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit. • Keep enough pressure on the bit to keep it drilling through the material. DDRRIILLLLIINNGG MMAASSOONNRRYY W WWH HHE EEN NN D DDR RRI IIL LLL LLI IIN NNG GG M MMA AAS SSO OON NNR RRY YY: :: • Masonry can be brittle so be careful not to apply too much pressure and crack the material. • Apply enough pressure to keep the bit cutting and not spinning in the will dull the edges of the bit. • Bricks and similar soft materials will require less pressure, concrete much more. DDRRIILLLLIINNGG WWOOOODD Use twist bits to drill holes in wood. Make sure out of the hole frequently to clear chips from may overheat. HHIINNTTSS FFOORR OOPPTTIIMMUUMM UUSSEE D DDR RRI IIL LLL LLI IIN NNG GG: :: • Keep the right amount of pressure little and the bit will spin without 16 • Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool. This will prevent stalling and leave a cleaner hole. • Use a block of wood to back up work pieces that may splinter. • Use spade bits when drilling large diameter holes in wood. • Use HSS drill bits when drilling in metal. • Use masonry bits when drilling in soft masonry. • Use a lubricant when drilling metals other than cast iron, aluminum, copper, and brass. • When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent slipping at higher speeds. • ...