Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
.. M MMa aai iin nnt tta aai iin nn l lla aab bbe eel lls ss a aan nnd dd n nna aam mme eep ppl lla aat tte ees ss o oon nn t tth hhe ee A AAn nng ggl lle ee G GGr rri iin nnd dde eer rr. .. These carry important information. If unreadable or missing, contact Alltrade for a replacement. W WWh hhe een nn u uus ssi iin nng gg t tth hhe ee A AAn nng ggl lle ee G GGr rri iin nnd dde eer rr, ,, a aal llw wwa aay yys ss m mma aai iin nnt tta aai iin nn a aa f ffi iir rrm mm g ggr rri iip pp o oon nn t tth hhe ee t tto ooo ool ll. .. Keep your hands well away from the grinding wheel or brush. Never reach underneath the Angle Grinder while the sanding disk is in motion. 7 I IIM MMP PPO OOR RRT TTA AAN NNT TT: :: Some of the following symbols may be used on your tool. Please 8 study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. CCOONNTTRROOLLSS AANNDD CCOOMMPPOONNEENNTTSS: : 1. ON/OFF Switch 2. Tool Body 2 6 4 3 1 AACCCCEESSSSOORRIIEESS: : 7. Grinding Wheel 8. Wrench SSYYMMBBOOLL NNAAMMEE EEXXPPLLAANNAATTIIOONN V Volts Voltage (Potential) A Amperes Current 3. Protective Guard Hz Hertz Frequency (Cycles per Second) 4. Anti Vibration Side Handle W Watt Power 5. Lock-on Switch Feature Kg Kilograms Weight for Continuous Use Alternating Current Type of Current 6. Replaceable Brush Cap Direct Current Type of Current SSYYMMBBOOLLSS Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal Class II Construction Denotes Double Insulation CCOOMMPPOONNEENNTT MMOODDEELL NNUUMMBBEERR WRENCH 690157 min Minutes Time s . .../min 1,2,3, … Seconds Diameter No load speed Revolutions per Minute Ring Selector Settings Time Size of Drill Bits, Grinding Wheels, etc. No-load Rotational Speed Revolutions, Surface Speed, Strokes, etc. per Minute Speed, Torque or Position Settings A AA S SS S SS E EE M MM B BB L LL Y YY M MM a aa k kk e ee s ss u uu r rr e ee y yy o oo u uu h hh a aa v vv e ee f ff u uu l ll l ll c cc o oo n nn t tt r rr o oo l ll o oo f ff t tt h hh e ee t tt o oo o oo l ll w ww h hh e ee n nn g gg r rr i ii n nn d dd i ii n nn g gg i ii n nn t tt o oo a aa c cc o oo r rr n nn e ee r rr a aa s ss a aa s ss h hh a aa r rr p pp , ,, s ss u uu d dd d dd e ee n nn m mm o oo v vv e ee m mm e ee n nn t tt m mm a aa y yy o oo c cc c cc u uu r rr w ww h hh e ee n nn t tt h hh e ee w ww h hh e ee e ee l ll c cc o oo n nn t tt a aa c cc t tt s ss a aa s ss e ee c cc o oo n nn d dd a aa r rr y yy s ss u uu r rr f ff a aa c cc e ee . .. 78 ATTACHING WHEELS WITH DEPRESSED CENTERS Always check the tool warning label for the recommended speed rating on accessories. Never run a wheel or brush over the rated speed. Accessories exceeding the recommended speed may fly apart and cause serious personal injury. Hubbed wheels do not require mounting flanges. • Check to make sure that the guard is fitted properly. Put the inner flange on the spindle. • Put the grinding wheel on the spindle and the inner flange. • When working with thin grinding wheels, fit the threaded outer flange with the raised area facing toward the wheel. • When working with thick grinding wheels, fit the threaded outer flange with the raised area facing away from the wheel. • Push in the spindle lock button. Turn the outer flange until it locks into place. • Once the spindle is locked, insert the enclosed wrench into the holes of the outer flange to tighten the outer flange properly. WARNING ATTACHING AUXILIARY HANDLE This tool comes with an auxiliary handle which can be attached to either side of the Angle Grinder, depending on the preference of the operator. This handle is necessary to maintain complete control of the tool and should be used at all times. Make sure this handle is always fastened securely. ATTACHING WHEEL GUARD Never brush or grind without the guard in place. Brushes are considered to be grinding wheels and must also be used with guards. • Always unplug the tool before attempting to change the guard or accessories. • Set the Angle Grinder on a flat surface with the spindle facing up. • Place the spring washer of the guard over the spindle. • Tighten the screw of the spring washer. • Make sure that the guard is securely tightened in place. 9 SPINDLE LOCK BUTTON AA T T A C H I N G G WW I R E E BB R U S H E S S Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are necessary. O OO P PP E EE R RR A AA T TT I II N NN G GG T TT H HH E EE A AA N NN G GG L LL E EE G GG R RR I II N NN D DD E EE R RR A AA l ll w ww a aa y yy s ss u uu n nn p pp l ll u uu g gg t tt h hh e ee t tt o oo o oo l ll b bb e ee f ff o oo r rr e ee a aa t tt t tt e ee m mm p pp t tt i ii n nn g gg t tt o oo c cc h hh a aa n nn g gg e ee t tt h hh e ee g gg u uu a aa r rr d dd o oo r rr a aa c cc c cc e ee s ss s ss o oo r rr i ii e ee s ss . .. For best tool control, material removal and minimal loading, keep the angle between the disc and the work surface at app...
Este manual também é adequado para os modelos :Brocas e shuropopverty - 4 1/2" ANGLE GRINDER 840557 (442.67 kb)