Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
• Always keep the driver bit straight to prevent damage to the screw. • Hold the Drill with both hands to ensure control if the bit should stick or slip. • To prevent wood from splitting, drill pilot holes into the wood before driving in the screws. 14 VARIABLE SPEED TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH: • The speed of the Cordless Drill depends on the amount of pressure you put on the trigger. • The more pressure you apply, the faster the Cordless Drill will go. • Release the pressure and the Cordless Drill will slow down. FORWARD / REVERSE AND TRIGGER LOCK LEVER Be sure the trigger is released when changing the position of the lever. Always store the tool in the “LOCKED/OFF” position. Always check the direction of the Cordless Drill's rotation before use. TO SELECT THE DIRECTIONS OF ROTATION: • To select forward Cordless Drill rotation, press the trigger lock from left to right flat against the Cordless Drill body. • To select reverse, press the trigger lock lever in the opposite direction. • The center position locks the tool. TORQUE SETTINGS To prevent damaging the tool or driving screw too deep into work piece, release the trigger when you feel the clutch slip. 13 TRIGGER LOCK TRIGGER SWITCH LOW SPEED HIGH SPEED CONTROL RING • Never try to start a stalled Drill by clicking the trigger switch “ON” and “OFF”. This may damage your tool. • To reduce jamming, always keep the Drill running when pulling the bit out of a finished hole. SCREWDRIVING: • Always use the correct type and size of screwdriver bit. • If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant. • Always hold the tool and screwdriver bit in a straight line with the screw. MAINTENANCE AND CLEANING Always remove the battery pack before attempting cleaning or maintenance. This Cordless Drill is lubricated before it leaves the factory. This lubrication should last for the life of the tool. No further lubrication is required. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the casing. Never immerse any part of the tool in a liquid. Always keep the ventilation openings clear. Always clean the battery pack using only a dry cloth. Do not use liquids. Always unplug the charger before cleaning it. Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth. Never open the Cordless Drill case, battery pack or charger. Do not attempt to repair the Cordless Drill, battery pack or charger yourself. Opening any of these parts will void your warranty. DRILLING METAL WHEN DRILLING HARD METALS: • Apply a lubricant, such as cutting oil, to the tip of the bit. • Start with a small hole then enlarge to the required size. Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit. • Keep enough pressure on the bit to keep it drilling through the material. DRILLING MASONRY WHEN DRILLING MASONRY: • Masonry can be brittle so be careful not to apply too much pressure and crack the material. • Apply enough pressure to keep the bit cutting and not spinning in the hole as this will dull the edges of the bit. • Bricks and similar soft materials will require less pressure, concrete will require much more. DRILLING WOOD Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits out of the hole frequently to clear chips from the flutes as an overburdened bit may overheat. HINTS FOR OPTIMUM USE DRILLING: • Keep the right amount of pressure in a straight line with the drill bit. Too little and the bit will spin without cutting, too much and the motor may stall. • Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool. This will prevent stalling and leave a cleaner hole. • Use a block of wood to back up work pieces that may splinter. • Use spade bits when drilling large diameter holes in wood. • Use HSS drill bits when drilling in metal. • Use masonry bits when drilling in soft masonry. • Use a lubricant when drilling metals other than cast iron, aluminum, copper, and brass. • When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent slipping at higher speeds. 15 PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times. At the end of their useful life, recycle batteries with due care for our environment. Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly. OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would like further information on the following products, please contact Alltrade Customer Service Department at 1-800-590-3723. Cordless Drills/Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rot...