Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
They turn red approximately ten seconds after they have been turned on. Each cooking zone is fitted with a control knob allowing you to select from 9 different temperature settings from a minimum of 1 to a maximum of 9. Extendable cooking zones The extendable radiant elements (B) are recognisable by the fact that they have a double heating zone. You can turn on only the smaller internal cooking zone or both the external and internal zones. The control knob allows you to choose between two power levels, which are both adjustable between a minimum value of 1 to a maximum of 9: • The lowest power level can be set by turning the knob clockwise from 1 to 9. • Turn the knob to completely (A) until you hear a slight click, to enable the maximum power level, which in turn can be adjusted between 9 and 1 by turning the knob anticlockwise. To restore the minimum power level, turn the knob and set it back to position 0. For double cooking zones, the first part of the knob movement activates the smaller cooking zone (internal). To activate both (internal and external), it is necessary to turn the knob completely (A) and then select the desired power level between 9 and 1. Residual heat indicator lights (only available on certain models) The indicator lights (C) indicate that the temperature of the corresponding cooking zones have exceeded 60°C, even after the heating element has been switched off. !The glue that is applied on the gaskets leaves some traces of grease on the glass. Before using the appliance, we recommend you eliminate these with a special non-abrasive cleaning product. During the first few hours of use there may be a smell of rubber which will disappear very quickly. To obtain the best results with your hob: • Use flat-bottomed pans to ensure that they adhere to the cooking zone perfectly. Always use pans with a diameter that is large enough to cover the hotplate fully, in order to use all the available heat. ilf T Make sure that the bottom of the cookware is always dry and clean to guarantee correct adherence and long life, not only for the cooking zones but also for the cookware itself. Avoid using the same cookware that is used on gas burners: the heat concentration on gas burners may deform the base of the pan, causing it not to adhere correctly. Never leave a cooking zone on without cookware on it because as it heats up and rapidly reaches the maximum level, it could damage the heating elements. 9 The electronic cooking programmer GB DISPLAY END OF _ COOKING icon DURATION — icon DECREASE TIME — button "t25>00 -XUU © c • 00 0 • UU&- 3 © SET TIME button CLOCK icon TIMER icon INCREASE TIME button Setting the clock ! The clock may be set when the oven Is switched off or when It Is switched on, provided that a the end time of a cooking cycle has not been programmed previously. After the appliance has been connected to the mains, or after a blackout, the icon and the four numerical digits on the DISPLAY will begin to flash. 1. Press the © button several times until the icon and the four digits on the display begin to flash. 2. Use the "+" and buttons to adjust the time; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the desired value. 3. Wait for 10 seconds or press the © button again to finalise the setting. Setting the timer ! This function does not interrupt cooking and does not affect the oven; it is simply used to activate the buzzer when the set amount of time has elapsed. 1. Press the © button several times until the icon and the three digits on the display begin to flash. 2. Use the "+" and "-" buttons to set the desired time; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the value. 3. Wait for 10 seconds or press the © button again to finalise the setting. The display will then show the time as it counts down. When this period of time has elapsed the buzzer will be activated. Programming cooking ! A cooking mode must be selected before programming can take place. Programming the cooking duration 1. Press the © button several times until the ^ icon and the three digits on the DISPLAY begin to flash. 2. Use the "+" and "-" buttons to set the desired duration; if you press and hold either button, the display will scroll through the values more quickly, making it quicker and easier to set the value. 3. Wait for 10 seconds or press the © button again to finalise the setting. 4. When the set time has elapsed, the text END appears on the DISPLAY, the oven will stop cooking and a buzzer sounds. • For example: it is 9:00 a.m. and a time of 1 hour and 15 minutes is programmed. The programme will stop automatically at 10:15 a.m. Setting the end time for a cooking mode ! A cooking duration must be set before the cooking end time can be scheduled. 1. Follow steps 1 to 3 to set the duration as de...
Este manual também é adequado para os modelos :Fornos - 7OH 637 C.1 IX RU/HA (2.13 mb)