Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Fornos - B44M42N0/01 (1.65 mb)
Fornos - B44M42N0/01 (1.64 mb)
Facilidade de uso
2. Disengage and pull out the door panel from the latch on the appliance door by lifting slightly. Removing the intermediate panel Before removing, make a note of the position in which the intermediate panel is fitted, so that you do not refit it the wrong way round later. 1.Push the brackets on the left and right-hand sides outwards (Fig. A) and unhook the intermediate panel. 2.Raise and pull out the intermediate panel (Fig. B). Cleaning Clean the door panels with glass cleaner and a soft cloth. Caution! Do not use any sharp or abrasive medium or a glass scraper. The glass could be damaged. Fitting the intermediate panel 1. Insert the intermediate panel into the three supports (Fig. A). 2.Press on the intermediate panel on the left and right next to the holders until it engages in the holders (Fig. B). Fitting the door panel 1. Insert the door panel into the two supports (Fig. A). 2.Press on the door panel on the left and right next to the holders until it engages in the holders (Fig. B). Cleaning the hook-in racks You can remove the hook-in racks for easier cleaning. a=Risk of burning due to hot components in the cooking compartment! Wait until the cooking compartment has cooled down. 1.Push the hook-in rack upwards at the front and unhook to the side (figure A). 2.Pull the hook-in rack forwards at the rear and unhook to the side (figure B). 3.Clean the hook-in rack with washing-up liquid and a sponge or brush. 4.Align the hook-in rack with the indentation (a) facing downwards, so that the shelf heights match. 5. Insert the hook-in rack at the rear as far as it will go and push to the rear (figure C). 6. Insert the hook-in rack at the front as far as it will go and push downwards (figure D). Faults and repairs It is not always necessary to call the after-sales service. Sometimes, you can find a remedy yourself. You will find some tips for troubleshooting in the following table. a=Risk of electric shock! ¦ Work on the appliance electronics may only be performed by a specialist. ¦ Always disconnect the appliance from the power supply when work is carried out on the electronics. Switch off the circuit breaker or remove the fuse from your household fuse box. Pr obl em P o ssi bl e cause Rem e di al a c t i on Electrical operation is malfunctioning ( e.g. Fuse defective Check fuses in the fuse box and replace if indicator lamps do not light up) necessary Liquid or thin dough runs to one side Appliance not installed level Check the appliance installation ( see the Installation instructions) ‹ : ‹‹ flashes in the clock display There was a power cut Reset the clock (see section: Electronic clock) Electronically controlled functions are mal- Energy surges (e. g. lightning strike) Reset the function concerned functioning Smoke is generated during roasting or grill- Fat is burning on the grill element Continue grilling or roasting until the fat on ing the grill element is burnt away Wire rack or universal pan inserted incor- Place the wire rack in the universal pan rectly and insert them together at a lower shelf height High levels of condensation are generated Normal occurrence (e. g. when baking with Open the appliance door briefly from time in the cooking compartment very moist toppings or roasting a large to time during operation joint) Enamelled accessories have light, matt Normal occurrence caused by dripping Not possible marks meat or fruit juices Door panels are misted up Normal occurrence caused by tempera- Heat the appliance up to 100 ° C and then ture differences switch off again after 5 minutes Replacing the oven light bulb 1. Unhook (Fig. B) the door seal at four points (Fig. A). Replace faulty oven light bulbs. You can obtain replacement light bulbs from customer service or specialist retailers: E14, 220 - 240 V, 40 W, heat resistant to 300 ° C. Only use these oven light bulbs. a= Risk of electric shock ! Disconnect the appliance from the power supply. Switch off the circuit breaker or remove the fuse from the household fuse box. 1. Place a tea towel in the cold cooking compartment to prevent damage. 2. Hook the door seal in at five further points (Fig. C) by turning 2. Turn the glass cover anticlockwise and remove it. the hooks slightly (Fig. D) . 3. Replace the oven light bulb with a bulb of the same type. 4. Screw on the glass cover again. 5. Remove the tea towel and switch on the circuit breaker. Note: If the glass cover cannot be unscrewed: use rubber gloves to turn it. You can order a special removal tool through the after-sales service (order no. 613634) Changing the door seal If the door seal is defective, it must be replaced. Replacement seals for your appliance can be obtained from the after- sales service. Unhooking the door seal The door seal is fixed in nine places. Hooking in the door seal 1. Hook (Fig. B) the door seal in at four points (Fig. A) . 2. Hook the door seal in at five further points (Fig. C) by turning it slightly ( Fig. D) . 3. Check that the door seal is seated...
Este manual também é adequado para os modelos :Fornos - B44M42N0/35 (1.77 mb)