Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Loosen baked- on food residues with a damp cloth and detergent. Leave the cooking compartment open to dry after cleaning. We recommend using oven cleaner if the oven is very dirty. If using oven cleaner, follow the manufacturer's instructions. Door seal Hot soapy water Hook- in rack/ tel- Hot soapy water escopic shelf Accessories Soak in hot soapy water. Clean with a brush and sponge or wash in the dishwasher. Keeping the appliance clean Clean the cooking compartment after each use, as dirt will bake on the next time it is heated up, and this can only be removed with difficulty. Always remove flecks of limescale, grease, starch and albumin (e. g. egg white) immediately. Where possible use the 3 Hot air operating mode. This operating mode creates less dirt. Removing and fitting the appliance door You can remove the appliance door to clean it more thoroughly. : Risk of injury! The hinges of the appliance door may snap shut with great force. Always open the hinge locking lever fully when removing the appliance door and close it fully after refitting. Do not reach into the hinge. : Risk of injury! If the appliance door has only been unhinged on one side, do not reach into the hinge. The hinge can snap back with great force. Call the aftersales service. Removing the appliance door 1. Open the appliance door fully. 2. Open the locking levers on the left and right- hand side fully. The hinges are secured and cannot snap closed. 3. Close the appliance door until resistance becomes noticeable ( figure A) . 4. With both hands, grip the door on the left and right- hand side, close the door a little more and pull it out (figure B) . Fitting the appliance door 1. Insert the hinges in the left and right-hand holders (figure C) . The notch on both hinges must engage. 2. Open the appliance door fully. 3. Close the locking levers on the left and right-hand side fully (figure D). The appliance door is secured and can no longer be removed. 4. Close the appliance door. Cleaning the door panels To assist with cleaning, the inner door panel can be removed from the appliance door. : Risk of injury! The components inside the appliance door may have sharp edges. Take care not to cut yourself. Wear protective gloves. : Risk of injury! The appliance must not be used again until the door panels and appliance door have been correctly fitted. Removing the door panel Note: Before removing, make a note of which way round the door panel is fitted, so that it is not refitted the wrong way round. 1. Unhook the appliance door and lay it on a soft, clean surface with the front side facing downwards (see section: Removing and fitting the appliance door) . 2. Pull off the cover at the top of the appliance door. Press in the tabs on the left and right using your fingers ( fig. A) . 3. Lift the door panel and pull it out (figure B). . . Cleaning Clean the door panel with glass cleaner and a soft cloth. : Risk of injury! Scratched glass in the appliance door may develop into a crack. Do not use a glass scraper, or sharp or abrasive cleaning aids or detergents. Fitting the door panel 1. Insert the door panel at an angle towards the back into both brackets as far as it will go. The smooth surface must face outwards. 2. Put the cover back in place and press on it until it clicks in place. 3. Refit the appliance door. Cleaning the hook-in racks You can remove the hook-in racks for easier cleaning. : Risk of burning due to hot components in the cooking compartment! Wait until the cooking compartment has cooled down. 1. Push the hook-in rack upwards at the front and unhook to the side ( figure A) . 2. Pull the hook- in rack forwards at the rear and unhook to the side ( figure B) . 3. Clean the hook-in rack with washing- up liquid and a sponge or brush. 4. Align the hook-in rack with the indentation ( a) facing downwards, so that the shelf heights match. 5. Insert the hook-in rack at the rear as far as it will go and push to the rear (figure C) . 6. Insert the hook-in rack at the front as far as it will go and push downwards (figure D) . Faults and repairs In the event of a fault, check the tips in the following table : Risk of electric shock! before calling the after-sales service. ¦ Work on the appliance electronics may only be performed by a specialist. ¦ Always disconnect the appliance from the power supply when work is carried out on the electronics. Switch off the circuit breaker or remove the fuse from your household fuse box. Problem Possible cause Remedial action Electrical operation is faulty (e.g. indicator Fuse defective Check fuses in the fuse box and replace if lamps no longer light up) necessary Liquid or runny dough runs to one side Appliance not installed level Check the appliance installation ( see the Installation instructions) Smoke is generated during roasting or Fat is burning on the grill element Continue grilling or roasting until the fat on grilling the grill element is burnt away Wire rack or universal pan inserted incor- Che...