• Password will be cleared and parental levels will be set to “ALL”. PASSWORD ENTER 55 TTo Chango Change the Pe the Passasswworord fd for Por Parental Contrarental Controlsols You can change your password for parental controls. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14. ENTER ENTER Select “PARENTAL LEVEL”. Enter your desired four- digit password (except for 4737). PARENTAL menu PASSWORD CHANGE PARENTAL LEVEL ALL 77 SETUP 66 Select the desired level. PARENTAL LEVEL ALL 8 7 [NC-17] 6 [R] To exit the menu 55 Select “PASSWORD CHANGE”. PARENTAL LEVEL ALL 77Enter your new four-digit password (except for 4737). To exit the menu ENTER Enter your desired four- digit password (except for 4737). or PASSWORD ENTER PARENTAL menu OTHERS Setting You can change the other functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14. E If you have set a password already, enter the current four-digit password. or or or ENTER 1 2 3 4 5 6 7 8 9 0 ENTER ENTER SETUP 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 CONTROL LEVELS • ALL: All parental locks are cancelled. • Level 8: DVD softwares of any grades (adult/general/children) can be played back. • Levels 7 to 2: Only DVD softwares intended for general use and children can be playedback. • Level 1: Only DVD softwares intended for children can be played back, with those intended for adult and general use prohibited. TIPS FOR LEVELS • 7 [NC-17]: No one under 17 admitted • 6 [R]: Restricted; under 17 requires accompanying parent or adult guardian • 4 [PG13]: Unsuitable for children under 13 • 3 [PG]: Parental Guidance suggested • 1 [G]: General Audience HintHint • DVD-Video discs may not respond to the parental lock settings. Make sure this function works with your DVD-Video discs. 5544 Select the desired item OTHERS menu 66 To exit the menu ANGLE ICON: (Default: ON) Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback. AUTO POWER OFF: (Default: ON) Set to “ON” to turn this unit off automatically after 30 minutes of no use. ANGLE ICON ON AUTO POWER OFF ON ON OFF OTHERS ENTER ANGLE ICON ON AUTO POWER OFF ON SETUP ENTERENTER ENTER or –16– EN Reset to the Default Setting (Except for PARENTAL Setting) HintHint • When you cancel to initialize at step 3), select “NO”. 22 443311 Select “INITIALIZE”. OK Select “YES”. NO YES SETUP To exit the menu Hit twice. SETUP STOP ENTER ENTER or or Information Troubleshooting Guide If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit consulting the following checklist. Problem Solution No power –Check if the AC power cord is properly connected. –Unplug the outlet once, and wait for 5-10seconds and then plug it in again. No sound or picture –Check if the TV is switched on. –Check the video connection. –Check the VIDEO/AUDIO cable connections to the TV. (See Connection to a TV) Distorted picture –Sometimes a small amount of picture distortion may appear. This is not a malfunction. –Connect the unit directly to the TV. Completely distorted picture or –Connect the unit directly to the TV. black/white picture with DVD –Make sure the disc is compatible with the unit. No sound or distorted sound –Adjust the volume. –Check that the speakers are connected correctly. No audio at digital output –Check the digital connections. –Check if the audio format of the selected audio language matches your receiver capabilities. No DTS audio is output –This unit does not support DTS audio. This is not a malfunction. Picture freezes momentarily –Check the disc for fingerprints/scratches and during playback clean with a soft cloth wiping from center to edge. –Clean the disc. Disc can’t be played –Clean the disc. –Ensure the disc label is facing up. –Check if the disc is defective by trying another disc. –Cancel the parental lock or change the control level. –Insert a correct disc that plays on this unit. –Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface. No return to start-up screen when –Reset the unit by switching the unit off, then on again. disc is removed The unit does not respond to –Aim the remote control directly at the sensor on the front of the unit. the remote control –Reduce the distance to the unit. –Replace the batteries in the remote control. –Re-insert the batteries with their polarities (+/– signs) as indicated. –Tune your radio to an empty AM station so that you hear a lot of noises. Then, turn the volume up. If you hear some signal sound from the radio by pressing buttons on the remote control, the remote control is working. Buttons do not work or the unit stops –To completely reset the unit, unplug the AC responding cord from the AC outlet for 5-10 seconds. The unit does not respond to some –Operations may not be permitted by the disc. operating commands during playback Refer to the instructions of the disc. The unit cannot read –Use a commonly available cleaning CD/...
)
