Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
You can not copy a DVD to a videotape. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. .You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording VCR] (this unit) ANT-IN ANT-OUT VIDEO OUT AUDIO OUT S-VIDEO OUT AUDIO OUT DIGITAL AUDIO OUT COAXIAL Y Cb Cr L R COMPONENT VIDEO OUT AUDIO IN VIDEO IN DVD/VCR VCR DVD R L R L ANT in [TV set] (Use for monitoring) RF cable (supplied) Audio/Video cables(not supplied) [Playing VCR] (another source) IN LEFT RIGHT OUT AUDIO VIDEO 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with a safety tab into the recording VCR. 3 Press SPEED on the recording VCR to select the desired recording speed (SP/SLP). 4 Select the “L1” or “L2”position on the recording VCR. .When you use the A/V input jacks on the back of the DVD/VCR, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons (o/p). .When you use the A/V input jacks on the front of the DVD/VCR, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons (o/p). 5 Press REC/OTR on the recording VCR. 6 Begin playback of the tape in the playing VCR. .For best results during dubbing, use the VCR’s front panel controls whenever possible. The remote control might affect the playing VCR’s operation. .Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. .You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR. 1 Turn on the TV and set the TV to channel 3. .If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See “RF OUTPUT CHANNEL” on page 13 for the detail). 2 Press VCR/TV on the recording VCR. MTS (Multi-Channel TelevisionSound) SYSTEM VCR When you play a VHS tape, or receive a broadcast on the VCR’s tuner, the current status will appear when you press STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI 1)* DISPLAY on the remote control. When you record a MTS broadcast signal, you need to set it to 2)* MTS mode. 1)* Press MENU and select "TV STEREO" or "SAP" by pressing K or L. Then, press B to select mode. To exit, press CLEAR/C.RESET. .Although a program may be broadcast in both stereo and sub audio, you must select the Recording mode to TV STEREO or SAP before you record a broadcast. 2)* Press MENU and select "AUDIO OUT" by pressing K or L. Then, press B. Next, select "HIFI" or "MONO" by pressing K or L. To exit, press CLEAR/C.RESET. .While the VCR is set in HIFI stereo mode, HIFI appears on the TV screen. While the VCR is set in monaural (MONO) mode, HIFI disappears from the TV screen. MTS RECORDING/MONITOR MODE Type of broadcast Display on the TV screen STEREO/SAP Selection Hi-Fi audio track (2-channel) Normal audio track Regular (monaural audio) -None- InvalidL- channel R-channel Mono Mono Mono Stereo broadcast STEREO I-nvalid-L R L+R Bilingual broadcast SAP TV STEREO* Main audio program Main audio program Main audio program SAP* Sub audio program Sub audio program Sub audio program Stereo & Bilingual broadcast STEREO SAP TV STEREO* L R L+R SAP* Sub audio program Sub audio program Sub audio program * –21– EN 1L25 AUTO REWIND REAL TIME TAPE COUNTER REAL TIME TAPE COUNTER When a tape reaches the end during recording, play-.This shows the elapsed recording or playback time back, or fast-forward, the tape will automatically in hours, minutes, and seconds. (The displayed time rewind to the beginning. After rewinding finishes, the will not change during blank portions of the tape.) VCR will eject the tape and switch itself off. .The indication will appear when the tape is rewound .The VCR will not rewind the tape automatically dur further than “0:00:00” on the tape counter. ing timer recording or One Touch Recording. PLAYING A DISC BASIC PLAYBACK Getting started .Turn on the power of the TV, amplifier and any other components which are connected to the DVD. .Make sure the TV and audio receiver (commercially available) are set to the correct channel. .Select DVD mode by pressing DVD on the remote control or output on the front panel. 1 Press POWER. .“Load” will appear briefly on the display panel. 2 Press OPEN/CLOSE to open disc loading tray. 3 Place the chosen disc in the tray, with the label facing up. DVD-V CD Notes .A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc. .With DVDs that use titles for playback program signals, playback may start from the second title, or it may skip these titles. .During the playback of a two layered disc, pictures may stop for a moment. This ...