Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
L C R L R 1 Audio input cable Note: Press tab to release cable connector. Acoustimass module connector panel When fully inserted into the jack, the connector locks in place. CAUTION: Do not place strain on the audio input cable, especially on the connection to the Acoustimass module. Placing excessive strain on the cable may cause damage to the cable connection at the Acoustimass module. When disconnecting the cable from the Acoustimass module, be sure to press the tab on the connector. AM259777_02_V.pdf • April 23, 2002 System Installation Instructions System Installation Instructions Connecting the antennas The rear panel of the media center provides connections for AM and FM antennas (Figure 11). Be sure to unwrap the bundled antenna wires and straighten them as much as possible to ensure the best reception. Note: Outdoor antennas may be used. To install an outdoor antenna, consult a qualified installer. Follow all safety instructions supplied with the antenna. Figure 11 Connections for the AM and FM antennas TV SENSOR IR EMITTER SERIAL DATA SPEAKER ZONES 1 2 1.1A 33V DC POWER AM FM 75 ANTENNA OPTICAL OPTICAL INPUT OUTPUT AUDIO OUTPUTS DIGITAL DIGITAL R L RECORD DIGITAL R L DIGITAL R L DIGITAL R L DIGITAL R L TAPE AUDIO INPUTS AUX VCR TV VIDEO INPUTS COMPOSITE S-VIDEO COMPOSITE S-VIDEO VIDEO OUTPUTS AM antenna lead FM dipole antenna lead Connecting an FM antenna Plug the connector on the FM dipole antenna lead into the FM antenna jack. Spread out the antenna arms. Change the orientation of the antenna arms to get optimum FM reception. Place the antenna as far from the media center and other components as possible. Connecting the AM antenna Note: To mount the AM antenna on a wall, follow the instructions enclosed with the antenna. 1. Plug the connector on the AM antenna lead into the AM antenna jack. 2. Stand the loop antenna on the base, following the instructions enclosed with the AM antenna. 3. Move the AM loop antenna as far as possible, at least 20 inches (50 cm), from the media center, and at least 2 feet (60 cm) from the Acoustimass® module. Experiment with the orientation of the loop for optimum AM reception. Connecting to a cable radio provider Some cable TV providers make FM radio signals available through the cable service to your home. This connection is made to the external FM jack on the back panel of the media center. To connect to this service, contact your cable TV provider for assistance. Note: Make sure that the cable radio installation includes a signal splitter so that only the FM radio band, not the cable TV band, is received by the media center. If necessary, contact a qualified installer. AM259777_02_V.pdf • April 23, 2002 System Installation Instructions System Installation Instructions Connecting your TV to the system 44 Figure 12 Media center-to-TV video and audio connections The media center provides audio and video connections for your TV. See Figure 12. Making audio connections Using the supplied stereo audio cable, connect the left (L) and right (R) audio outputs on the rear panel of your TV to the L and R TV audio inputs on the rear panel of the media center (Figure 12). Making video connections These connections will vary according to the type of cable you use as described below. Composite video Using the supplied video cable (with yellow connectors), connect the COMPOSITE video output on the rear panel of the media center to the VIDEO INPUT on the rear panel of your TV (Figure 12). S-video The S-VIDEO OUTPUT provides a higher quality picture on your TV than the COMPOSITE VIDEO OUTPUT. This jack is provided on many TVs. To make this connection you will need to use the S-video cable included with your system. Component video Some newer televisions are equipped with component video input jacks. Component video consists of three separate video signals (Y, Pb, and Pr) which deliver a very high quality picture to your TV. TV SENSOR IR EMITTER SERIAL DATA SPEAKER ZONES 1 2 1.1A 33V DC POWER AM FM 75 ANTENNA OPTICAL OPTICAL INPUT OUTPUT AUDIO OUTPUTS DIGITAL DIGITAL R L RECORD DIGITAL R L DIGITAL R L DIGITAL R L DIGITAL R L TAPE AUDIO INPUTS AUX VCR TV VIDEO INPUTS COMPOSITE S-VIDEO COMPOSITE S-VIDEO VIDEO OUTPUTS TV connector panel TV AUDIO VIDEO OUT IN R L AM259777_02_V.pdf • April 23, 2002 System Installation Instructions System Installation Instructions To make component video connections, you will need video-grade cables for the Y, Pb, and Pr jacks and the Bose® component video adapter (Figure 13). This adapter plugs into the S-VIDEO and COMPOSITE outputs. Your system will send the correct signals to these jacks when you change the video output setting to YPbPr. See your LIFESTYLE® 28/35 system operating guide for instructions on how to change system settings. Note: Component video jacks are often color-coded and it is essential that you match the color-coded connections with the cables. Figure 13 Media Center Component video adapter Your TV Component video adapter S-VIDEO O...
Este manual também é adequado para os modelos :DVD-player - AM259777 (1.39 mb)