Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center. I A'Warning/V' I Improper use of the grounded plug can result in the risk of electrical shock. If the power j cord is damaged, have it replaced by an authorized Avanti Products service center. I_.__— Reversing the Door Swing of Vour Wine Cooler This wine cooler has the capability of either opening the dcor from the left or right side. The unit is delivered to ycu with the door opening from the left side. Should you desire to reverse the opening direction, please follow these instructions. NOTE: Before reversing the door, the power must be shut off. AM parts removed must be saved to do the reinstallation of the door. 1. Remove the two plugs (16) located in the back of top cover. 2. Remove the two screws (15) holding the top cover (12). 3. Lift the tcp cover up slightly from the back and then push it forward in order to unhook the front of the top cover so it can be detached from the lock plate. 4. Hold the top cover and keep it from dropping to the ground because the wires are (14) connected to the controller box underneath rhe top cover. 5. Remove the two screws (11) holding the controller box cover (17). 6. Remove the controller box cover (17) and unplug the connector (13) from the socket (18) on the PC8 board (10). 7. Place the top cover (12) on a padded surface to prevent scratching it. 8. Remove the upper right hinge (8), holding the door in place. 9. Lift the door and place it on a padded surface to prevent scratching it. 10. Lay the unit on its back against a solid surface at an angle of no less than 45 degrees. 11. Remove the upper hinge pin (9) from the hinge (8). 12. Replace the right upper hinge (8) to its original location. 13. Remove the two bolts (2) that hold the lower right hinge (5). 14. Remove the front leg (3) and the lower hinge pin (4) from the lower hinge (5). 15. Save the lower hinge assembly for later use. 16. Remove the lower left hinge (1) and transfer it to the opposite side, reversing the direction 180 degrees, where the lower right hinge (5) was previously located. 17. Transfer the lower hinge previously removed to the opposite side, where the left lower hinge (1) was located, reversing the direction 180 degrees. Then insert the front leg (3), the two bolts and the pin (4). 18. While holding the door in the closed position, secure the lower hinge on the left side of the frame, by screwing the bolts (2) in. Do not tighten until door is level. 19. Remove the upper left hinge (7) and insert the top hinge pin (9). 20. Replace the upper left hinge (7) with pin (9) to secure the door. 21. Plug the connector (13) to the socket (18) on the PCB (10) board. 22. Replace the controller box cover (12) by inserting the two screws previously removed in step 5. 23. Place the top cover by inserting all two screws previously removed in step 2. 24. Insert all the plugs previously removed in step 1. FIGURE I Position prior to door reversai 1. Lower left hinge 2. Bolt 3. Front leg 4. Lower hinge pin • 5. Lower right hinge 6. Lock plate 7. Upper left hinge 8. Upper right hinge 9. Upper hinge pin FIGURE II Position after door reversal 10. PCB 11. Screw 12. Top cover 13. Connector 14. Wiring 15. Screw 16. Plugs 17. Controller box cover 18. Socket IMPORTANT SAFEGUARDS Do not store food :n wine cooler, as interior temperature may not get cool enough to prevent spoilage. As a natural result of condensation, in summer months or areas of high humidity, the glass door may cuiid up moisture on the outside. Just wipe it away. - OPERATING YOUR WINE COOLER It is recommended you install the wine cooler in a place where the ambient temperature is between 72-78 degrees Fahrenheit. If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The range of 45-65 degrees Fahrenheit may not be reached. If :he interior light is left on, the temperature inside the wine cooler will be higher. Recommenced Temperatures for Chilling Wine Red Wines: 60-65: F Dry/White Wines 50-5913 F Sparkling Wines 45-493 F Rose Wines 49-51s F The above temperatures may fluctuate depending on whether or not the interior bulb is on or off or whether the bottles are located on the upper/middle or lower section. ■ i M-itMH— HOW TO USE THE BUTTONS ON THE DISPLAY PANEL: You can set the temperature as you desire by pushing the button or &). When you push the two buttons for the first time, the LED readout will show the original temperature set at previous time (the temperature preset at the factory is 50° F). The temperature that you desire to set will increase 13 F or 1 'C if you push the ...
Este manual também é adequado para os modelos :DVD-player - WC600CL (317.25 kb)