Assessments - 2, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
By pressing You can TV [/1 Turn the TV on or off 2 (volume) +/– Adjust the volume of the TV t (TV/video) Switch the TV’s input source between the TV and other input sources Note Depending on the connected unit, you may not be able to control your TV using all or some of the buttons on the supplied remote. Controlling other TVs with the remote You can control the sound level, input source, and power switch of non-Sony TVs as well. If your TV is listed in the table below, set the appropriate manufacturer’s code. 1 While holding down TV [/1, press the number buttons to select your TV’s manufacturer’s code (see the table below). 2 Release TV [/1. Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Manufacturer Code number Sony 01 (default) Aiwa 01 (default) Grundig 11 Hitachi 24 JVC 33 LG 06 Loewe 06 Panasonic 17, 49 Philips 06, 08 Samsung 06, 71 Sanyo 25 Sharp 29 Thomson 43 Toshiba 38 Notes • When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. • Depending on the connected unit, you may not be able to control your TV using all or some of the buttons on the supplied remote. Hookups Step 6: Quick Setup Follow the steps below to make the minimum number of basic adjustments for using the player. To skip an adjustment, press >. To return to the previous adjustment, press .. 1 Turn on the TV. 2 Press [/1. 3 Switch the input selector on your TV so that the signal from the player appears on the TV screen. “Press [ENTER] to run QUICK SETUP” appears at the bottom of the screen. If this message does not appear, select “QUICK” under “SETUP” in the Control Menu to run Quick Setup (page 56). 4 Press ENTER without inserting a disc. The Setup Display for selecting the language used in the on-screen display appears. ENTER The player displays the menu and subtitles in the selected language. 6 Press ENTER. The Setup Display for selecting the aspect ratio of the TV to be connected appears. SCREEN SETUP TV TYPE: 16:9 4:3 LETTER BOX 4:3 PAN SCAN OFF SCREEN SAVER: BACKGROUND: 16:9 PROGRESSIVE (COMPONENT OUT ONLY): LINE: MODE (PROGRESSIVE): 4:3 OUTPUT: AUTO FULL 7 Press X/x to select the setting that matches your TV type. . If you have a wide-screen TV or a 4:3 standard TV with a wide-screen mode • 16:9 (page 57) . If you have a 4:3 standard TV • 4:3 LETTER BOX or 4:3 PAN SCAN (page 57) 5 Press X/x to select a language. LANGUAGE SETUP OSD: MENU: AUDIO: SUBTITLE: ITALIANO ESPANOL NEDERLANDS DANSK SVENSKA FRANCAIS ENGLISH ENGLISH DEUTSCH 8 Press ENTER. The Setup Display for selecting the type of video signal output from the LINE (RGB)-TV jack appears. SCREEN SETUP TV TYPE: 16:9 SCREEN SAVER: ON BACKGROUND: JACKET PICTURE LINE: VIDEO PROGRESSIVE (COMPONENT OUT ONLY) VIDEO MODE (PROGRESSIVE): S VIDEO 4:3 OUTPUT: RGB (COMPONENT OFF) 9 Press X/x to select the type of signal you want to output from the LINE (RGB)-TV jack. . Video signals • VIDEO (page 58) . S video signals • S VIDEO (page 58) . RGB signals • RGB (COMPONENT OFF) (page 58) 10Press ENTER. The Setup Display for selecting the type of jack used to connect your audio component such as an amplifier (receiver) appears. Is this player connected to an amplifier (receiver)? Select the type of jack you are using. LINE OUTPUT L/R(AUDIO) DIGITAL OUTPUT YES NO 11Press X/x to select the type of jack (if any) you are using to connect to an audio component, then press ENTER. If you did not connect an audio component, select “NO,” then go to step 15. If you connected an audio component using just an audio cord, select “YES: LINE OUTPUT L/R (AUDIO),” then go to step 15. If you connected an audio component using either digital coaxial cord/HDMI cord, select “YES: DIGITAL OUTPUT.” 12Press X/x to select the type of Dolby Digital signal you wish to send to your audio component. If your audio component has a Dolby Digital decoder, select “DOLBY DIGITAL.” Otherwise, select “D-PCM.” AUDIO SETUP AUDIO DRC: STANDARD DOWNMIX: DOLBY SURROUND DIGITAL OUT: ON DOLBY DIGITAL: D-PCM MPEG: D-PCM DTS: DOLBY DIGITAL 48kHz/96kHz PCM: 48kHz/16bit 13Press ENTER. “DTS” is selected. AUDIO SETUP AUDIO DRC: STANDARD DOWNMIX: DOLBY SURROUND DIGITAL OUT: ON DOLBY DIGITAL: D-PCM MPEG: PCM DTS: OFF 48kHz/96kHz PCM: OFF ON 14Press X/x to select whether or not you wish to send a DTS signal to your audio component. If your audio component has a DTS decoder, select “ON.” Otherwise, select “OFF.” 15Press ENTER. Quick Setup is finished and connections are complete. If your audio component has an MPEG audio decoder, set “MPEG” to “MPEG” (page 61). Note When “PhotoTV HD” mode is activated (page 50), the selection for “TV TYPE” is skipped. Hookups 4 Press Z on the player, and place a Depending on the DVD or VIDEO CD, some operations may be different or restricted. Playback Playing Discs Refer to the operating instructions supplied with y...