Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Select Languages English This part of the manual is to prevent damages or data loss. Read carefully and use the device properly. Do not place it under the direct sunlight. Place it so that it sits on its side on a flat surface. Do not scratch or place a label on the disc. Handle the disc with caution to prevent damage from external shock. Do not expose it to severe temperature fluctuations. (Exposure to such environment may cause congealing.) Select Languages English This part of the manual is to prevent damages or data loss. Read carefully and use the device properly. Do not touch the surface of the disc. Place your fingers on the edge of the disc to hold. Clean the disc lightly with soft cotton cloth, starting from the center and move to the edge of the disc. Use only disc cleaning liquids. Do not use benzene, paint thinner, or any other solvents. If the disc surface becomes dirty with fingerprints, foreign substances or dust, the disc may not function properly. Select Languages English On/Off Lamp Meaning Disc Lead-In Green: Blinks every 0.3 seconds. Writing Green: Blinks every 0.3 seconds. Reading Green: Blinks every 0.3 seconds. Audio Playback [Analog Mode] Green: Blinks every 0.3 seconds. Audio Playback [Digital Mode] Green: Blinks every 0.3 seconds. Standby Off No Disc Off The indicator light turns off when the drive is not in use (standby) after disc lead-in. Select Languages English Problem Meaning / Solution The tray won't open. See if the PC on. Make sure the power cable within the PC is connected properly. If the tray still won't open with the power on, turn the power off and insert a pin(paper clip) into the emergency hole to open. The tray won't close. Make sure the disc has been inserted properly. The PC is not working properly. See if the jumper(s) is properly connected to the Master/Slave Selection port. See if the drive is properly connected to the PC. See if the floppy disc remains in the PC. The drive is not working properly. See if the drive is connected properly to the PC. See if the device drive program has been installed properly. No sound is heard from an audio Check whether the audio cable is correctly connected to the sound CD. output terminal on the drive and the sound card CD-IN terminal. Check that the sound card is operational. If the Digital CD Audio Output box is checked, no sound comes out of the analog audio outputterminal of the driver. Check the condition of the CD and wipe the surface of the CD clean before use. The Window OS can't detect the See if the device drive program has been installed properly. drive. Can be an OS problem. Try reinstalling the Windows OS program. The system won't read the disc. See if the system detects the drive. Make sure you use the types of discs that are supported by the drive. See if the on/off light turns into green. Make sure you inserted the disc with the label facing up. Make sure you are using the right program for disc playback. See if the disc is clean. See if any congealing has occurred. Make sure the region code of the drive matches the disc number. The drive is connected to the Your sound card is using AT BUS interface. sound card but cannot seem to Connect the card to the E-IDE port or replace the card with a new detect it. card with the built-in E-IDE interface capacity. Select Languages English DVD Writers record data on the disc by applying laser light onto the surface of the CD DVD, and therefore writing errors may occur if you use a damaged CD DVD , for example . Be sure to eliminate the following error-causing elements before you start writing: * The following settings are recommended for all DVD Writers: Avoid a situation that requires multitasking , and remove turn off the screen saver. A buffer underrun may occur if the system multitasks while the DVD±R/RW CD-RW drive is writing/erasing. Block any outside attempt to access the host PC during a writing session. An error may occur if another user accesses the printer connected to his/her the system via the network during a writing session. Disable the CD auto - run feature of the CD. Inserting an auto - run-enabled CD in to another drive connected to the same system during a writing/erasing session may cause an error. How to disable the auto-run feature: Windows 98/ME GO to Start Settings Control Panel System Hardware Device Manger CD- ROM Settings . Disable Insert AutoRun. It is recommended that you use the image file format when you write a large number of small- sized files. When there are a large number of small-sized files to write , the system's transmission rate drops and the Superlink feature works at a more frequent rate, resulting in lower writing quality. If you are doing a CD-to-CD write , it is not necessary to check to see if you have available space on your hard disc beforehand. However, in the case of image files, it is recommended that you be sur...
Este manual também é adequado para os modelos :DVD-player - SH-S182D (2.15 mb)
DVD-player - TS-H652G (2.15 mb)
DVD-player - TS-H652H (2.15 mb)
DVD-player - TS-H652M (2.15 mb)