Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If you press STOP twice, this is a ‘complete stop’, and playback resumes from the beginning of the disc. Front panel menu navigation Should you need to navigate a disc or title menu from the front panel, use PAUSE for ‘up’, STOP for ‘down’ , for ‘right’, for ‘left’ and PLAY for ‘OK’. Using the remote control CD/DVD Ensure that DVD mode is selected using the CD/DVD toggle button. The ‘DVD’ LED above the CD/DVD button is lit briefly when DVD mode is selected. 0–9 keypad This allows direct access to individual tracks on audio CDs. To select a track, press the corresponding keypad button followed by OK. For tracks greater than 9, enter the digits in sequence. For example, to play track 15, press 1, then 5, then OK. DISP (display) Dims or turns the DV88PLUS’s display on or off. Turning the display off generally gives a slight improvement in sound quality. Pressing DISP once turns the display off; twice dims the display. To restore the display to full brightness, press DISP a third time. Standby Press Standby to toggle the standby state of the DVD player. Note that Arcam CD players are not controlled by this button. OKANGLECDDVDSETUPSTATUSSRCHZOOMAUDIOMEMRTNPMODESUBTTITLEMENURPTCLEAR0PROGA-B789DISP456CDDVD123MUTEOPENCD/DVD REMOTECR-314 CLEAR Use CLEAR within the ‘Program’ and ‘Bookmark’ menus to clear a numeric field (see pages 12–13). A–B This button enables you to repeat a selected section from the disc (see page 12). PROG (program) You can program a selection of up to 20 chapters/tracks from a disc to play in any order. Press PROG to access the ’Programme’ menu (see pages 13 and 15). RPT (repeat) Press RPT to cycle through the repeat play options. Slow play Press or on the remote control to play slow forward or backwards. There are four speeds of slow playback: 1/5, 1/4, 1/3 and 1/2. Press the button repeatedly to cycle through the different speeds. To resume normal playback speed, press PLAY. Note that slow play does not apply to audio CDs. Fast play and Skip chapter/tracks Play fast ( ) and Skip ( ) chapters/tracks in both directions (see page 9). OPEN Opens and closes the disc tray. Cursor pad and OK button Use the cursor pad to navigate the On Screen Display (OSD) and menu pages. Confirm your selection with the OK button. MUTE Stops sound to the speaker outputs of certain Arcam amplifiers. Playback control Pause (), Play () and Stop () (see page 9). Volume +/– Adjusts the volume on Arcam remote-controllable amplifiers. Note that the volume (+/–) controls and MUTE button have no effect on the audio output level of the DVD players. Advanced controls These buttons are described on the facing page. NOTE: Remember to install the two AAA batteries supplied before trying to use your remote control. Do not place anything in front of the display area on the DVD player (where the IR receiver is located), or the remote control may not work. Advanced controls MEM (memorise) It is possible to ‘bookmark’ up to three points on a DVD title, so you can quickly jump to those parts of the title again. Press MEM to access the ‘Bookmark’ menu. SUBT (subtitle) Press SUBT on the remote control to cycle through the available subtitle languages, including ‘OFF’. Some discs force subtitles on, over-riding player set up. TITLE Press TITLE to access the DVD’s ‘Title’ menu. Note that this feature only applies to multi-title discs. MENU Press MENU to access the DVD ‘Disc’ menu. This navigation menu is specific to a disc and varies for each title, but typically offers facilities to select chapters, languages, and view extra material such as trailers or documentaries. Once the menu has been accessed, use the cursor pad to move around the menu and press OK to activate a menu ‘button’. P MODE Press P MODE to toggle random playback ZOOM Press ZOOM to enlarge a particular area of the picture. Each press of the ZOOM button increases the zoom, normally until a maximum of 4x enlargement is reached (although the amount of zoom possible varies depending on the type of disc: in some cases no zooming is possible). Pressing ZOOM when the maximum enlargement has been reached returns the image to normal size. While using the zoom function, the cursor pad can be used to move around within the image. The zoom function can also be used when playback is paused. Note that a zoom level of x1.5 is particularly useful if the output from the DVD player is in a different screen format to your TV. A zoom of x1.5 when a ‘widescreeen’ image is displayed on a 4:3 TV causes the bars at the top and bottom of the screen to disappear (although the sides of the image are lost); a zoom of x1.5 when a 4:3 image is displayed on a widescreen TV causes the bars at the side of the image to disappear (although the top and bottom of the image are lost). ANGLESETUPSTATUSSRCHZOOMAUDIOMEMRTNPMODESUBTTITLEMENU RTN (return) Press RTN to move back through the DVD ‘Disc’ and ‘Title’ menus. Note that this feature is only of use with discs using multi-level menus. SRCH (search) It is po...