Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Further information about disc layer changes can often be found on the rear cover of the disc packaging. The picture freezes for a moment at random points in a film The disc is dirty or damaged A damaged or dirty disc may cause audio and/or video drop-outs to occur (and may be accompanied by increased drive noise). Clean or replace the disc. PROBLEMS WITH AUDIO OUTPUT Problem Possible cause Solution No sound! Incorrect input selected on audio device (decoder, receiver, amplifier, etc.) Select the appropriate input on the audio device (consult that product’s handbook) Bad audio connection (analogue or digital) from DV27A to audio device Check connections at both ends and, if necessary, try an alternative cable No sound from the centre/rear speakers A two-channel source, such as a CD, is being played There is no fault The ‘Audio’ is set incorrectly in the ‘Setup’ menu Enter the ‘Setup’ menu and change the ‘Audio’ setting to ‘Bitstream/6ch.’ (see page 9) The centre/rear speakers are configured incorrectly in the ‘Setup’ menu Enter the ‘Setup’ menu and change the settings on the ‘Speakers’ page to reflect your speaker configuration (see page 10) Bad connection between the DV27A and the amplifier/receiver or the amplifier/receiver and the speakers Check connections at both end and, if necessary, try alternative cables PROBLEMS WITH DISC PLAYABILITY Problem Possible cause Solution Player loads disc but does not play, or play-back halts unexpectedly (perhaps with the message ‘Invalid Region’ being displayed) Not all discs play automatically when loaded Press PLAY There is a fault in the manufacturing of the disc Some discs are manufactured incorrectly, and are known to cause problems on ARCAM (and other) DVD players. Naturally, we aim to support all discs; from time-to-time we issue software upgrades for the player that fixes new problems of which we are aware. Please contact ARCAM customer support for further details. The disc is from the wrong region DVD discs are designed to be played only in the region that they are sold in (for example, discs from the USA are ‘Region 1’ and discs from Europe are ‘Region 2’). Your player is factory-configured to play discs from the region it is to be sold in, and may not play discs from other regions. Disc does not play and ‘Bad Disc’ is displayed The disc is damaged or dirty, or does not contain any files that the DV27A can handle Remove disc from tray and check surfaces for damage or dirt. In the case of a CD-ROM, check that the disc contains valid MP3/WMA or JPEG files. Cannot enter player ‘Setup’ menu Disc still playing Stop disc, and press SETUP on remote control (see page 7) Some MP3/WMA files cannot be played There are some restrictions on the type of MP3/WMA files that the DV27A player can play See page 20 of this Handbook The player takes a long time to identify a CD Since this is a DVD player (primarily), it checks for discs in the following order: DVDs, SVCDs, VCDs, CDs. Therefore it takes longer to identify a CD than any other disc type. The front-panel display is not illuminated The front-panel display has been switched off The front panel supports three different levels of illumination. Press the ‘DISP’ button on the remote control to select your preferred level BEFORE CONTACTING CUSTOMER SERVICES If any problem persists or cannot be cured using the advice given, either contact your Arcam dealer or Arcam customer support. Before contacting Arcam customer services with a question however, it is useful to have various version and region numbers available. This information is displayed in the top left corner of the screen when the player is first switched on (or brought out of standby). This information is shown for approximately two seconds, and is the following format: software version/ drive version/ Arcam shipping region/ DVD region Technical specifications General Power Requirements 115V or 230V AC, set by voltage selector switch on rear panel Power consumption <45VA Dimensions 430mm x 90mm x 280mm Weight net: 6.2kg; packed: 7.8kg Video outputs Composite video 1 x gold plated phono: 1V pk-pk into 75. S-Video 1 x 4-pin mini-DIN: Y 1V pk-pk in 75., C 0.3V pk-pk into 75. SCART socket with RGB video All 0.7V into 75., composite video 1V into 75., and stereo audio. Auto switching of TV with aspect ratio control Progressive scan video Pure Progressive™ motion adaptive 4-field processing by Silicon Image Corporation3 gold plated phono sockets: Y 1V pk-pk into 75.; Pb 0.7V pk-pk into 75.; Pr 0.7V pk-pk into 75. Audio outputs Analogue audio outputs 6 channel outputs on gold plated phono sockets Output level 2.2V rms at 0dB signal, 4V rms on left and right with HDCD discs Frequency response 20Hz to 20kHz (+0.1db, –0.5dB) THD+N <0.005% for 1kHz 0dB signal, measured 22Hz–22kHz, unweighted Signal-to-noise ratio 105dB, measured 20Hz–20kHz, unweighted Digital audio output (IEC958) PCM/Dolby digital/MPEG/DTS on gold plated phono (coaxial) and TOSLINK (optical) Accessories supp...