Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
OPTION 1: By removing the existing switch and not jumping the board the sold out will work, but not reset unless the pump door switch is manually reset after each refill. If the switch is not manually reset the light will not go out even after installing new product. OPTION 2: To disable the sold out feature jumpers are added to the control board in the sold out plug location. The sold out will now be disabled and never come on. Installation of these options are described below. Parts List Description Part Number Qty Bracket 720201471 1 Sold Out Jumper Board 11749 4 Jumper Switch 720302204 1 Spacer 720705306 1 Screw Plastic #8 x .” 07015001 2 Screw 6-32 x 3/8” 0700203 2 Washer .145x.5x .03 07301043 2 Screw 6-32 x 1/4 0700201 2 Latch 720532112 1 Catch 720202415 1 Tools Required • Hex Screw Driver • Electrical Tape FIGURE 1 Revision Date: June 30, 2004 Revision: C © 2004, IMI Cornelius Inc. - 1 -Publication Number: 729011146INS Door Latch Assembly Installation Instructions INSTALLATION IMPORTANT: Disconnect power from machine before starting this procedure! 1. Remove the top cover of the machine. A. Remove two screws from rear of top. B. To remove cover open door and pull cover forward. FIGURE 2 FIGURE 3 2. Remove the side panel of the machine. A. Remove latch cover plate. B. Remove 2 screws holding splash guard. NOTE: When reassembling latch guard use the #8 PLASTIC screws supplied. FIGURE 4 FIGURE 5 C. Remove one screw from lower rear on right D. Slide panel forward to remove. side panel. NOTE: Do not loose plastic spacers located on panel clips. FIGURE 6 FIGURE 7 Publication Number: 729011146INS - 2 - © 2004, IMI Cornelius Inc. Door Latch Assembly Installation Instructions 3. Remove and replace door catch. A. Remove (2) 8-32 screws holding existing B. Replace catch with new catch assembly. door catch. Fasten to door with 8-32 x 5/8” screws. FIGURE 9 FIGURE 8 4. Remove and replace cabinet catch. A. Pull back tape back exposing catch/switch. B. Remove and save insulation putty to be reinstalled later. FIGURE 10 FIGURE 11 C. Remove (2) 6-32 screws holding existing D. Remove latch/switch from wire harness. latch/switch. FIGURE 13 FIGURE 12 © 2004, IMI Cornelius Inc. - 3 -Publication Number: 729011146INS Door Latch Assembly Installation Instructions E. Insert slotted holes into new latch. F. Attach bracket and latch to cabinet frame using (2) 6-32 x 3/8” screws and washers. FIGURE 14 G. Close door and adjust cabinet bracket using the 6-32 screws. Door should slightly compress the door seal. FIGURE 16 5. Connect cabinet interrupt switch jumper wire. A. Plug one end of black spade end jumper in each end of existing cable. FIGURE 18 FIGURE 15 H. Check lower and upper door to assure seal. If not adjust bracket until it properly seals. FIGURE 17 B. Wrap a piece of electrical tape on both ends to prevent wires from coming loose. FIGURE 19 Publication Number: 729011146INS - 4 - © 2004, IMI Cornelius Inc. Door Latch Assembly Installation Instructions C. Route wires in existing cavity and reinstall insulation putty and replace tape. FIGURE 21 FIGURE 20 D. Replace side panels by sliding panels for-E. Replace latch cover plate. ward to engage panel tabs. Make sure plas-NOTE: When reassembling latch guard use tic spacers are located on panel clips before the #8 PLASTIC screws supplied if holes are assembling. Replace all screws that were stripped. previously dissembled. FIGURE 22 FIGURE 23 THIS COMPLETES THE LATCH ASSEMBLY PROCEDURE. If the machine is to use OPTION 1 “DOOR RESET OPTION” allowing sold out to function complete the procedure by replacing all machine covers and guards. IF OPTION 2 IS SELECTED CONTINUE WITH PROCEDURE 6. Installing sold out defeat jumpers. A. Remove screw, holding electrical box to B. Pull control box from machine. frame. FIGURE 25 FIGURE 24 © 2004, IMI Cornelius Inc. - 5 -Publication Number: 729011146INS Door Latch Assembly Installation Instructions C. Remove cover from box. D. Locate the 2 pin plug that says “SOLD OUT” on the control board. There will be one for each pump. Disconnect these connectors. There will be (4) total in a four flavor machine. FIGURE 26 FIGURE 27 E. Replace the connectors with the “SOLD OUT” jumpers. FIGURE 28 THIS COMPLETES THE LATCH ASSEMBLY PROCEDURE for OPTION 2 “SOLD OUT DISABLED OPTION” disabling the sold out function. Complete the procedure by replacing all machine covers and guards. If machine does not function after reassembly make sure control box is properly seated in mating connector. Publication Number: 729011146INS - 6 - © 2004, IMI Cornelius Inc. ...