Assessments - 5, GPA: 3.4
(
)
)
|
Facilidade de uso
Folio w the gas supplier's instructions. * If you cannot reach your gas supplier, call the fire department. ■ Installation and service must be performed by a qualified installer, service agency or the gas supplier. JK AVERTISSEMENT: Assurez-vous de bien suivre les instructions données dans cette notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter tout dommage matériel, toute blessure ou la mort. ■Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre appareil. ■ QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ: * Ne pas tenter d’allumer d’appareil. * Ne touchez à aucun interrupteur. Ne pas vous servir des téléphones se trouvant dans le bâtiment où vous vous trouvez.. * Évacuez la pièce, le bâtiment ou la zone. * Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les instructions du fournisseur. * Si vous ne pouvez rej oindre le fournisseur de gaz, appelez le service des incendies. ■L’installation et l’entretien doivent être assurés par un installateur ou un service d’entretien qualifié ou par le fournisseur de gaz. .American Dryer Corp. For replacement parts, contact the distributor from which the dryer was purchased or @ American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 Telephone: (508)678-9000 / Fax: (508)678-9447 e-mail: techsupport@amdry.com 080395 ADC Part No. 112235 Retain This Manual In A Safe Place For Future Reference American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation/operator's manual included with the dryer. The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location. FOR YOUR SAFETY POUR VOTRE SÉCURITÉ Do not store or use gasoline or Ne pas entreposerai utiliser d’essence other flammable vapors or liquids ni d’autres vapeurs ou liquides in the vicinity of this or any other inflammables dans le voisinage de cet appliance. appareil ou de yout autre appareil. We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models. Important For your convenience, log the following information: DATE OF PURCHASE _ MODEL NO. __ADG-310 DISTRIBUTORS NAME _ Serial Number(s) _ Replacement parts can be obtained from your distributor or the ADC factory. When ordering replacement parts from the factory, you can FAX your order to ADC at (508) 678-9447 or telephone your orders directly to the ADC Parts Department at (508) 678-9000. Please specify the dryer model number and serial number in addition to the description and part number, so that your order is processed accurately and promptly. “IMPORTANTNOTE TO PURCHASER” Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer. ADG-310 Forward Tilt/Manual Door with Heater Fault Indication MACHINE OPERATION SUMMARY This AD-310 incorporates one (1) emergency stop button located on the right front of the machine. This button is "TURN TO RELEASE," and must be in the released mode to power the machine. When the emergency button is released, the Phase 5 microcomputer's display will light. To turn on the AD-310's control voltage, press the green "ON" button located on the right front control panel. NOTE: If a Sprinkler System is incorporated in the machine, the Sprinkler System must be powered for the control power to engage. Refer to the AD-310 Sprinkler System Addendum (ADC Part No. 112233) for sprinkler system information. The ADG-310 has two (2) electronic controllers: • Phase 5 micro-computer...for material drying. • Micro-1 PLC (Programmable Logic Controller)...for burner status monitoring, end of cycle light control, forward tilt, and jog functions. The Phase 5 micro-computer responds to keypad commands only when the AD-310's doors and lint screen drawer are both closed. The Micro-1 PLC (Programmable Logic Controller) monitors burner status during a drying cycle, and stops the drying cycle if any fault is detected with the burners. It also controls the "FORWARD TILT" (Rear Up) and "LEVEL" (Rear Down) functions of the AGD-310's tumbler section, in addition to forward and reverse tumbler manual jog selections. ADG-310 DETAIL OPERATION INFORMATION Anytime the airjet signal is asserted the "END OF CYCLE" light (located on the top of the tumbler section) will begin to flash once a second and remain on until the "LOAD D...