Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Please use the following instructions to ensure correct installation and use. Keep these notes in a safe place for future reference. Checking Pack Contents Unpack your chime kit and identify the following parts: • Chime • Chime bracket • Bell push • CR2032 battery for bell push • 4 self-adhesive icons strips (2 pre- fitted on chime) • 2 screws for push • 2 screws for chime wall bracket • 2 wall plugs • Adhesive pad You will need: • A Phillips-head screwdriver • A small flat-bladed screwdriver • A 1/4-in. (6 mm) masonry drill • 4 LR14 “C” alkaline batteries Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Quick Start The bell push supplied with this kit is pre-programmed to operate with the chime. You need to do the following to get started: • Open the bell push • Install the push battery • Install the chime batteries • Check the chime switch setting • Check the volume setting When you operate the bell push, the chime will sound and the first icon will flash. If you have additional pushes or you want to assign a different icon to your push, you will need to follow the programming procedure. Open the Bell Push M27269A Insert a flat-bladed screwdriver into the slot A, at the base of the push. Carefully lever the cover and base apart (Fig. 1). Fig. 1 Install the Bell Push Battery M27153CR2032+CR2032+ Insert the CR2032 coin cell. Ensure the face marked “+” is facing up (Fig. 2). Fig. 2 Install the Chime Batteries To remove the chime battery cover, press at point C and slide the cover back, then lift off. Insert 4 LR14 “C” alkaline batteries (not supplied). Observe polarity as marked inside the battery compartment (Fig. 3). M27270C Fig. 3 Switch Positions Mute with flash on To keep the flash on and turn the sound off, set switch (D) to position 1. Flash off with sound on To turn the blue flashing light off, set switch (D) to position 3. Normal operation For normal operation (sound and flashing light on), set switch (D) to position 2. 1 2 3M27286D Fig. 4 Sliding Window M27271E23156 Release the catch (E) and slide open the window. Shown with number icon strips. Fig. 5 Volume Control The volume control is behind the sliding window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to the desired volume. M27272VOLUMECONTROL23156 Fig. 6 Use of Icons In addition to the chime sounds, your chime has a visual indication to show which device has activated it. An icon will illuminate when the chime is activated by a bell push or another compatible device. The chime supports six icons: MAINDOORBACKDOORALERTSYMBOLINTRUDERTELEPHONEPAGER/ KEY FOBM27289 The “Main door” and “Back door” icons are usually used for bell pushes. The other icons are intended for use with other compatible devices, such as wireless motion detectors and telephone ring detectors (check availability). Icons numbered 1 to 6 are also included. The icons are self-adhesive, supplied in strips of 3. They can be changed, if required, by opening the sliding window of the chime and gently peeling off the strips. If desired, the strips can be cut into individual icons and fixed to the chime in a different order. Use the Programming procedure to change the Icon associated with a push. Use of Icons M27290 Programming Procedure Learn procedure To enable your chime to learn the identity of your bell push: • Press the l button and keep it pressed. Each Icon will light in turn. When the Icon you want is lit, release the button. • While the Icon you have selected is lit, operate your push. The chime will sound. The Icon will flash. Unlearn procedure If you want to remove a push from the chime’s memory: • Press the l button and keep it pressed. Each Icon will light in turn. When the Icon associated with the push to be unlearned is lit, release the button. • Press and hold both l & buttons until a “beep” sound is heard. Changing the Tune Operate the push. While the Icon is flashing, press the button. Press the button again and the tune will change. Repeat until the tune you want plays. Recall Function A short push of the l button will flash the Icon that was last in use. Chime Sounds To hear the chime sounds without operating the bell push, press the button. Press the button again and the tune will change. Mount the Bell Push Mount using either the double-sided adhesive pad, or the screws provided (see Fig 7). Test your push before mounting. Avoid mounting to metal structures. M27155TOP Fig. 7 Chime Position The chime can be free-standing or wall-mounted using the wall bracket provided. If wall mounting is preferred, screw the bracket to the wall (see Fig 8). The chime hooks onto the...