Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 5). 2. Setthepush button jumpers to match the chime receiver code. See “Code and Tune Setting” section. 3. Test range. Temporarily position push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 4. Mount push button. 598-1077-02 -2 Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Unplug wireless chime (if applicable). 2. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 5). . The push button and chime both have eight different jumper locations.The jumper positions 1 through 7 areused forsetting the code. 4. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. 598-1077-02 - Tune Settings Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Availableonselectedchimes). Thefactory setting isfortheDing-Dong tune (or Westminster, when available).This tune can be changed by following the instructions below. • Ding (one note tune) Push button: Add a jumper to location 8. • Ding-Dong (two note tune) Push button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. You may purchase any ACE® wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. 598-1077-02 -4 Remove screw to open access door Tune Setting (Not used on all models) Back of Chime 12 45678 Push Button Battery Replacement Install an alkaline type A23 12 Volt battery. See diagram inside push button for correct battery orientation. * Code Settings 1-7 Must Match Both Push Button and Chime Inside Push 12 45678 Button Tune Setting Note: Some models might require the use of tweezers to remove and replace the jumpers. 598-1077-02 -5 Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages , 4, and 5). • Check orientation of push button battery (See page 5). • Check charge of push button and chime batteries (if applicable), replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 1 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. The range of the wireless chime can vary with location, temperature and battery condition. 598-1077-02 -6 Technical Service Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store. If you experience a problem, follow this guide.You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7: 0 AM to 4: 0 PM CST (M-F).You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following information availa...
Este manual também é adequado para os modelos :Portas e janelas - 3087590 (AC-6197) (114.9 kb)