Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Be careful when opening.DOnOtover extend the front door when opening or damage to hinges may occur. Pull From Here to Open CHiME installatiOn IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 10 below. Note: Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. 1. Verify transformer power rating. Power must be supplied from a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer (Heath®/Zenith models 122C, 121AC, or 125C). 2. Remove cover from existing chime. 3. Label all wires before disconnecting. Using masking tape, mark each wire according to existing chime terminal markings. • “F” – Front Push Button Wire • “T” – Transformer Wire • “R” – Rear Push Button Wire* 4. Disconnect all wires from existing chime. 5. Remove existing chime base from wall. 6. Determinechimemounting location. IMPORTANT:Thischime requires more mounting surface than most other chimes. Use the dimensions in Figure 1 to help determine the proper location of the chime. If chime will not fit in the same location as the existing chime, then contact a licensed electrician to move the existing wiring to a more suitable location. Illustrations may vary from actual chime unit. Figure 1 - Chime Dimensions Continued 51 /8" 58 1/2" 12 11/16" Wire Entrance Hole Mounting Hole (x2) CHiME installatiOn IMPORTANT: Proper installation requires a diode on the front door push button. See Diode Installation Instructions (page 5) after completing steps 1 through 10 below. Note: Electrical work must be in accordance with national and local electrical codes. If in doubt, consult a qualified electrician. 1. Verify transformer power rating. Power must be supplied from a 16 Volt AC, 10 Watt or a 16 Volt AC, 15 Watt transformer (Heath®/Zenith models 122C, 121AC, or 125C). 2. Remove cover from existing chime. 3. Label all wires before disconnecting. Using masking tape, mark each wire according to existing chime terminal markings. • “F” – Front Push Button Wire • “T” – Transformer Wire • “R” – Rear Push Button Wire* 4. Disconnect all wires from existing chime. 5. Remove existing chime base from wall. 6. Determinechimemounting location. IMPORTANT:Thischime requires more mounting surface than most other chimes. Use the dimensions in Figure 1 to help determine the proper location of the chime. If chime will not fit in the same location as the existing chime, then contact a licensed electrician to move the existing wiring to a more suitable location. Illustrations may vary from actual chime unit. Figure 1 - Chime Dimensions Continued 51 /8" 58 1/2" 12 11/16" Wire Entrance Hole Mounting Hole (x2) - - 7. Mount chime cover with base to wall using screws and anchors provided. • Use the dimensions shown in Figure 2 to properly locate mounting holes. • Drill 1/4" (6.4 mm) diameter pilot hole and insert wall anchors. • Insertmountingscrewsintowallanchors(leaveapproximately 5/8" (15.9 mm) of the screw threads exposed). • Route wires through wire entrance hole in new chime base. • Align mounting keyholes on rear of chime with screws and place cover on screws. • Tighten screws securely. 8. Remove 3/8" (9.5 mm) of insulation from each wire and push wires into the chime quick connects (See Figure 3). • Push wire “F” into first quick connect terminal. • Push wire “T” into second quick connect terminal. • Push wire “R” into third quick connect terminal. 9. Connect diode to front push button (see page 5). 10. Press push button to verify chime works properly. If chime does not complete eight-note melody, see Troubleshooting, page 8. * Note: Some installations may not include rear door push button. Figure 2 - Mounting Screw Location Dimensions Figure 3 - Connecting Wires to Chime 7" 3/8" FTRRFTChime Wire Quick Connects To Remove Wires, Depress Orange Tab While Pulling Wire Out of Quick Connect DiODE installatiOn instruCtiOns a small electrical component called a “diode” is required for this chime to play the entire eight-note tune.this diode must be installed on the terminal screws of the front door push button (see Figure 4). If not already installed on push button, attach supplied diode as shown below. If, with the diode in place, the chime does not play the complete eight-note melody, see Troubleshooting, page 8. Figure 4 - Attaching Diode to Front Door Push Button Diode Front Door Push Button (Styles May Vary) Front Door Push Button (Styles May Vary) -5 -6 attaCHing tuBEs tO CHiME attach spring Hangers to Brass tubes 1. Locate the drilled holes in one end of each tube (see Figure 5). 2. Insert one end of spring hanger into one hole. 3. Compress the hanger just enough to insert the other end into the second hole. Hang Brass tubes in Chime 1. Insert tubes through opening in the bottom of the chime (see Figure 6). 2. Hang the tubes on the hanging brackets using the spring hangers installed above. Note: Ma...