Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 6. Mount chime. There are three different ways to mount the chime depending upon the model of chime purchased. Determine which model you purchased Figure 4 below. Mount the chime according to the instructions for your chime. 1 2 3 4 5 6 7 ON Basic Chime with Separate Chime with Attached Chime Decorative Cover Decorative Cover Style of push button and chime may vary from illustration. -2- 598-1149-01 Basic Chime: 1. Remove batteries from chime. 2. Place chime against wall and verify the chime is level. 3. Use chime holes as a template (see Figure 5). Drill 7/32" diameter pilot hole for 2 wall anchors (provided) and insert anchors. 4. Insert 2 screws (provided) through holes in back of chime. 5. Using arrow inside chime unit as a guide, mount chime with arrow pointing up (see Figure 5). Do not tighten completely. 6. Verify chime is level and tighten screws securely. 7. Replace batteries (see Figure 3). Snap cover onto chime base. -3598- 1149-01 1 2 3 4 5 6 7 ON Holes for Wall Mounting Figure 5 Mount Chime Unit with Arrow Pointing Up 1 2 3 4 5 6 7 ON Chime with Separate Decorative Cover: 1. Slide cover pin onto rear of chime as shown in Figure 6. Pin must be assembled to base prior to mounting base to wall (pin may be pre-assembled). 2. Follow directions under “Basic Chime” to mount chime base to wall. 3. Hang cover on cover pin. Figure 6 Top of Chime Back of Chime Cover Pin Cover Pin Installed on Chime Back Chime with Attached Decorative Cover: 1. Mount hanger to chime (hanger Predrilled may be pre-assembled): Hanger • Place hanger over predrilled Holes holes (either in top or bottom panel). • Connect hanger to chime using 2 #4 screws (provided). 2. Determine where chime is to be mounted. 3. Drill 1/4" diameter pilot hole for wall anchor (provided) and insert anchor. 4. Screw #8 screw (provided) into anchor. Leave 1/16" gap between screw head and wall. 5. Place hanger over screw to mount chime. Hanger #4 Screws Figure 7 -4-598-1149-01 Tune Settings Your wireless chime has different selectable tunes: Dong (one note) and Ding- Dong (two note). The factory setting is for the Ding-Dong tune. This tune can 1234567812345678be changed by following the instructions below. • Dong (one note tune) Inside Push Button: Add jumper to location 8. • Ding-Dong (two note tune) Inside Push Button: Remove jumper from location 8. Note: All ACE® models have both front and back door tune capabilities. We recommend the back door use the Dong tune and the front door use the Ding- Dong tune. Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. Tune Setting Push Button Set Push Button Set for One Note Tune for Two Note Tune (Dong) (Ding-Dong) Figure 8 - Inside Push Button Note: Some models might require the use of tweezers to remove and replace the jumpers. 598-1149-01 -5 Troubleshooting A. Low Battery Indicator: When the push button designated for the “Ding-Dong” tone is pressed, only a “Dong” note will play when battery power is low in chime unit. B. Chime does not sound: • Make sure push button and chime codes are the same (see Figure 9). • Check orientation of push button and chime batteries (See diagram inside push button and chime for correct battery orientation.) • Check charge of push button and chime batteries, replace if necessary. C. Chime sounds when not intended (false triggers): Chime is receiving interference from another wireless device; change the code setting (see Code Setting below). D. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. E. Code Setting: It is recommended to only change one code position at a time and then check to see if system is functioning properly. 1. Open the cases and locate the jumpers on the push button and the switches on the chime (see Figure 9). 2. The push button has eight different jumper locations and the chime has seven switches. Jumper positions 1 through 7 on the push button and the switches on the chime are used for setting the code. 3. To change the code, either: • Add a jumper to the push button and set the matching chime switch to “ON” or... • Remove a jumper on the push button and set the matching chime switch to “OFF” or... • Move a jumper in the push button from one location to another.Turn “OFF” the chime switch matching the first location and turn “ON” the chime switch matching the new location of the jumper. Note: Code positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. Note: Uni...