Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 3). 2. Plug in wireless chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to bypass this safety feature. 3. Test range. Temporarily position push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. DANGER: Electric shock hazard. Do not open chime. No serviceable components inside. If strobe fails to flash, replace chime. © 2007 HeathCo LLC 598-1143-01 4. Mount push button. Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. Code and Strobe/Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Unplug wireless chime. 2. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 3). 3. Jumper positions 1 through 7 are used for setting the code. 4. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. -2-598-1143-01 Strobe/Tune Settings Your wireless chime has different selectable tunes: Ding-Dong (two flashes/two notes/two flashes) or Westminster (eight flashes/eight notes/eight flashes). The factory setting is for the Westminster tune. This tune can be changed by following the instructions below. • Ding-Dong (Two note tune) Strobe will flash two times, play the two note tune, then flash two more times. Push button: Add a jumper to location 8. • Westminster (Eight note tune) Strobe will flash eight times, play the eight note tune, then flash eight more times. Push button: Remove jumper from location 8. Push button Battery Replacement Remove screw to InstallanalkalinetypeA2312Voltbattery. open access door See diagram inside push button for correct battery orientation. * Code Settings 1-7 Must Match Both Push Button and Chime Tune Setting 1234567 Back of Chime 12345678 Inside Push Button Note: Some models might require the use of tweezers to remove and replace the jumpers. 598-1143-01 -3 Troubleshooting Chime does not sound and strobe does not flash: • Make sure push button and chime codes are the same (See pages 2 and 3). • Check orientation of push button battery (See page 3). • Check push button battery charge, replace if necessary. Batteries seem OK, but the chime and strobe do not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. The range of the wireless chime can vary with location, temperature and battery condition. DANGER: Electric shock hazard. Do not open chime. No serviceable components inside. If strobe fails to flash, replace chime. Technical Service Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F).You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product Regulatory Information This device complies with Part 15 of the FCC...